AWB OD200-IDU Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 114

background image

Gateway Configuration

5-8

5

LAN

The OD200 must have a valid IP address for management using a web browser and
to support other features. The unit has a default IP address of 192.168.1.1. You can
use this IP address or assign another address that is compatible with your existing
local network. The unit can also be enabled as a Dynamic Host Configuration
Protocol (DHCP) server to allocate IP addresses to local PCs.

LAN Settings

The OD200 includes a DHCP server that can assign temporary IP addresses to any
attached host requesting the service. Addresses are assigned to clients from a
common address pool configured on the unit. Configure an address pool by
specifying start and end IP addresses. Be sure not to include the unit's IP address in
the address pool range.

Figure 5-8 LAN Settings

IP Address

– The IP address of the unit. Valid IP addresses consist of four decimal

numbers, 0 to 255, separated by periods.The default setting is 192.168.1.1.

Subnet Mask

– Indicates the local subnet mask is fixed as 255.255.255.0.

The Gateway acts as DHCP Server

– Check this box to enable the DHCP server.

IP Pool Starting/Ending Address

– Specifies the start and end IP address of a

range that the DHCP server can allocate to DHCP clients. You can specify a single
address or an address range. Note that the address pool range is always in the
same subnet as the unit’s IP setting. (Default: 192.168.1.2 to 192.168.1.254)

«
...
46
47
48
49
50
...
»

Содержание OD200-IDU



















































































































Отзывы:

Нет отзывов

Похожие инструкции для OD200-IDU

Бренд: ICP DAS USA Страницы: 33

SentryPlus Alert

Бренд: Watts Страницы: 12

Бренд: H3C Страницы: 29

Бренд: Digi Страницы: 6

Бренд: IXXAT Страницы: 21

MediaPack MP-262

Бренд: AudioCodes Страницы: 2

Бренд: Berker Страницы: 4

Smart Wireless Gateway 1420

Бренд: Emerson Страницы: 96

Бренд: Nokia Страницы: 107

Бренд: ICC Страницы: 54

Бренд: ZyXEL Communications Страницы: 2

Бренд: ZyXEL Communications Страницы: 617

Бренд: Watchguard Страницы: 18

Бренд: FarSite Communications Страницы: 2

Бренд: SignalFire Страницы: 31

AMILO Pro V3525 Edition

Бренд: Fujitsu Siemens Computers Страницы: 29

SURFboard SBG7400AC2

Бренд: Arris Страницы: 22

Бренд: Speed Touch Страницы: 676

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды