AWB OD200-IDU Скачать руководство пользователя страница 69

Страница: 69 / 114

SIP Setting

7-3

SIP Register

– The IP address of the SIP registrar server. A registrar is a server that

accepts SIP register requests and places the information it receives in those
requests into the location service for the domain it handles.

SIP Register Port Number

– The TCP port number used by the VoIP service

provider’s register server. (Range: 0-65535; Default: 5060)

Proxy Address

– Address of the VoIP service provider SIP proxy server.

Proxy Port

– The TCP port number used by the VoIP service provider’s SIP proxy

server. (Range: 0-65535; Default: 5060)

SIP Setting

From the VoIP SIP Setting page you can configure SIP parameter details.

Figure 7-2 SIP Setting

RTP Packetization Time

– Specifies a maximum amount of time for transmission of

a RTP data packet. (Options: 10, 20, 30 ms; Default: 20 ms)

RTP Port Base/Limit

– The Real-time Transport Protocol (RTP) and Real-time

Control Protocol (RTCP) do not use specified port numbers. You can specify a port
range that the RTP and RTCP traffic can use. Enter the port Base and Limit to define
the range. (Range: 1024-65535)

Stun Server

– STUN (Simple Traversal of UDP through NAT (Network Address

Translation)) is a protocol that assists devices behind a NAT firewall or router with

Содержание OD200-IDU



















































































































Результаты поиска

Содержание OD200-IDU

Отзывы:

Похожие инструкции для OD200-IDU

Бренды по названию

Популярные бренды

AWB OD200-IDU, Руководство оператора

Результаты поиска

Содержание OD200-IDU

Отзывы:

Похожие инструкции для OD200-IDU

Бренды по названию

Популярные бренды