AVS Electronics ONE DT, Руководство пользователя

Страница: 24 / 80

- 24 -
E
N
G
TERMINAL BLOCK
-
Power negative
+ 12 V power positive =
C
Alarm contact of the sensor with capacity of 100 mA
Normally closed sensor idle
NC
T Anti-tampering contact of the sensor with capacity of 100 mA
Normally closed
T
SW1 - BALANCING RESISTANCES
DIP
1
TAMPER
(see S1)
ON 10 kohm resistance inserted
OFF DEFAULT 10 kohm resistance excluded
DIP
2
TAMPER
(see S1)
ON
5.6 kohm resistance inserted
OFF DEFAULT
5.6 kohm resistance excluded
DIP
3
TAMPER
(see S1)
ON 4.7 kohm resistance inserted
OFF DEFAULT 4.7 kohm resistance excluded
DIP
4
TAMPER
(see S1)
ON 2.2 kohm resistance inserted
OFF DEFAULT
2.2 kohm resistance excluded
DIP
5
ALARM
(in parallel)
ON
10 kohm resistance inserted
OFF DEFAULT 10 kohm resistance excluded
DIP
6
ALARM
(in parallel)
ON 5.6 kohm resistance inserted
OFF DEFAULT 5.6 kohm resistance excluded
DIP
7
ALARM
(in parallel)
ON
4.7 kohm resistance inserted
OFF DEFAULT
4.7 kohm resistance excluded
DIP
8
ALARM
(in parallel)
ON
2.2 kohm resistance inserted
OFF DEFAULT 2.2 kohm resistance excluded
S1 MANAGING THE TAMPER CONTACT
1 - 2
The resistance, configurable via DIP SWITCHES 1, 2, 3 and 4 of SW1, is in
series between the ALARM contact and that of the TAMPER (DEFAULT)
2 - 3
The resistance, configurable via DIP SWITCHES 1, 2, 3 and 4 of SW1, is in
parallel with the TAMPER contact
It is possible to insert balancing resistances for both the alarm and tamper contacts.
For the settings, refer to the tables for
S1 and SW1 .
SW2 - FUNCTIONS
DIP 1
ON DEFAULT Led Enable
OFF Led Excluded
DIP 2
ON Anti-mask active Tamper relay
OFF DEFAULT Anti-mask active Alarm relay
DIP 3
ON Anti-mask Microwave Active (Model OnE DT only)
OFF DEFAULT Anti-mask Microwave Disabled (Model OnE DT only)
DIP 4 OFF DEFAULT In this configuration the infrared has a default sensitivity (designed for classic use) and
performs a digital analysis of the signal .
DIP 5 OFF
DIP 4 ON LOW
In this configuration the infrared has a low sensitivity compared to the default and performs a
digital analysis of the signal that is stricter than the default and considers a double pulse
DIP 5 OFF
DIP 4 OFF MEDIA
In this configuration the infrared has a average sensitivity compared to the default and
performs a digital analysis of the signal that is stricter than the default
DIP 5 ON
DIP 4 ON HIGH In this configuration the infrared has high sensitivity and detects any signal by analyzing the
amplitude
DIP 5 ON
DIP 6
ON Yellow LED displays status of the Microwave (Model OnE DT only)
OFF DEFAULT Yellow LED displays status of the Anti-mask
DIP 7
ON Anti-mask Infrared Active
OFF DEFAULT Anti-mask Infrared Disabled
DIP 8
ON
Tamper Accelerometer enabled
OFF DEFAULT
Tamper Accelerometer excluded
OnE PA e OnE DT
O
N
1
2
3
4
5
6
7
8
O
N
1
2
3
4
5
6
7
8
SW1
SW2
S1
1
3
- +
C NC T
1
T
2
RV1
RV2
TAMPER
L1
L2
2
CONNECTIONS WITH S1 in
position 1 - 2
If a TAMPER resistance is inserted
in series using DIPs 1, 2, 3 and 4
of SW1, terminal blocks NC and
T2 must not be used
O
N
O
N
1
2
3
4
5
6
7
x x
- +
L L
S1
NOTE: When you simultaneously set more than one of DIPs 1, 2, 3 and 4 (Tamper) to ON, the relative heating elements
will be placed in parallel with each other. The same principle applies to DIPs 5, 6, 7 and 8 (Alarm)