Avital 5103 страница 21 Скачать руководство пользователя

Страница: 21 / 64

➤

Auxiliary harness (H2), 6-pin connector

H2/1

LIGHT BLUE

(-) 200mA 2nd UNLOCK OUTPUT

This wire produces a (-) 200mA output for progressive locks in which the driver

door unlocks first and the remaining locks unlock with a second press of the

unlock button.

H2/2

WHITE/BLACK

(-) 200mA PROGRAMMABLE AUX 3 OUTPUT

This wire provides 200 mA programmable output whenever the transmitter

button(s) controlling AUX 3 is pressed. This output can be programmed to pro-

vide the following types of outputs

Validity: Output that sends a signal as long as the transmission is re-

•

ceived.

Latched: Output that sends a signal when the AUX channel button is

•

pressed and continues until the same button is pressed.

Latched, reset with ignition: Similar to the latched output, this type of output

•

turns On the first time the AUX channel button is pressed, and turns Off the

next time the same button is pressed. This type of output additionally stops

and resets whenever the ignition is turned On and then Off.

30 seconds (60, 90) timed: The output sends a continuous signal for 30

•

seconds.

Note:

Bitwriter® programs from 1 to 90 seconds.

Sat mode,

bank selector

AUDIO

PWR

REW

PLAY/PROG

DISC-

DISC+

11:53

XM1-1

CH-001

VOL

SCAN

SOUND

AM/FM

CD/AUX

SAT

RADIO

SEEK

SKIP

RPT

DISP -

MODE

A.SEL

RDM

TUNE

AUTO

OFF

DUAL

A/C

MODE

Channel control

Содержание 5103
































































Результаты поиска

Содержание 5103

Отзывы:

Похожие инструкции для 5103

Бренды по названию

Популярные бренды

Avital 5103, Руководство по установке

Результаты поиска

Содержание 5103

Отзывы:

Похожие инструкции для 5103

Бренды по названию

Популярные бренды