Avital 5103 страница 46 Скачать руководство пользователя

Страница: 46 / 64

Feature descriptions

The features of the system are described below. Features that have additional

settings when programming with the Bitwriter® are indicated by the following

icon:

Default settings are in bold. The numbers in parentheses indicate the number

of times the Status LED flashes.

➤

Menu 1 - Basic

1-1 Active/

Passive

Arming:

When active arming, the system arms only when

the transmitter is used. When set to passive, the system arms automatically 30

seconds after the last door is closed. To alert the consumer of passive arming,

the siren chirps 20 seconds after the door is closed. This provides the consumer

with an audible warning prior to the system actually arming. At the 30 second

mark, the system arms, but the siren does not chirp.

1-2 Chirps On/

Off

This feature controls the chirps that confirm the arming and

disarming of the system.

1-3 Ignition Lock

/Off:

When turned On, the doors lock 3 seconds after the

ignition is turned On.

1-4 Ignition unlock

On/

Off

: When ON this feature unlocks the doors when the

ignition is turned Off

1-5 Active

/Passive

Locking

: If passive arming is selected in Feature 1-1, then

the system can be programmed to either lock the doors when passive arming oc-

curs, or only lock the doors when the system is armed via the transmitter. Active

locking means the system will not lock the doors when it passively arms. Passive

locking means that the system will lock the doors when it passively arms.

Note:

Remember, when passive arming is selected, the unit will chirp 20 sec-

onds after the last door is closed. The system does not actually arm or lock the

doors until 30 seconds after the door has been closed.

Содержание 5103
































































Результаты поиска

Содержание 5103

Отзывы:

Похожие инструкции для 5103

Бренды по названию

Популярные бренды

Avital 5103, Руководство по установке

Результаты поиска

Содержание 5103

Отзывы:

Похожие инструкции для 5103

Бренды по названию

Популярные бренды