manualshive.com logo in svg

AVGear AVG-UHMS44PRO, Руководство пользователя

Поделиться
Скачать
AVGear AVG-UHMS44PRO Скачать руководство пользователя страница 28

AVG-UHMS44PRO 

 

5.4. TCP/IP Control 

The AVG-UHMS44PRO 4K HDBaseT 4x4 Matrix Switcher boasts an optional 
TCP/IP port for IP control. 

Default settings: IP: 192.168.0.178; Subnet Mast: 255.255.255.0; Gateway: 
192.168.0.1; Port: 4001.  

IP & gateway settings can be changed as needed, the Port cannot be changed. 

Connect the Ethernet port of the control device and TCP/IP port of the 4K HDBaseT 
4x4 Matrix Switcher, and set the same network subnet for the 2 devices, users are 
then able to control the device via the web-based GUI or TCP/IP communication 
software. 

 

5.4.1. Control Modes 

The AVH-UHMS44PRO 4K HDBaseT 4x4 Matrix Switcher can be controlled by a PC 
without Ethernet access or PC(s) within a LAN.

 

  Controlled by PC 

Connect a computer to the TCP/IP port of the 4K HDBaseT 4x4 Matrix Switcher, and 
set its network subnet to the same as 

the 4K HDBaseT 4x4 Matrix Switcher’s 

(Default: 192.168.0.178). 

 

 

  Controlled by PC(s) in LAN 

Connect the 4K HDBaseT 4x4 Matrix Switcher, a router and several PCs to setup a 
LAN (as shown in the following figure). Set the network subnet of 4K HDBaseT 4x4 
M

atrix Switcher to the same as the router’s, then PCs within the LAN are able to 

control the 4K HDBaseT 4x4 Matrix Switcher. 

Same network 
subnet as the 
switcher 

Содержание AVG-UHMS44PRO






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды