background image

2-2  

Operating Instructions 

B a t t er y   L i f e 

The MW S Battery Status LEDs are located on the top-left side of the Power Panel. To use the 
Battery Status LEDs, the MW S must be on.  

If you leave the battery charger plugged in and constantly charging 

when the MWS is not in 

use (turn MWS power off)

, the battery life is maximized for the application.  The charger does 

not overcharge the batteries.  

The MW S has signal lights to indicate the battery status as follows.  The following voltages are 
an approximation and should be used for reference only. 

Flashing Orange 

Warning!  The batteries need immediate charging.  The MW S beeps 
continuously to alert you of this condition. (Early models have red lights 
instead of orange). 

Flashing Yellow 

Caution!  Finish printing the batch, then recharge the MW S. The batteries 
are getting low. 

Flashing Green 

Go!  The batteries are charged to approximately 75% or better capacity. 

If the CHARGE light does not turn on, make sure the charger is properly connected to the 
batteries and the charger has AC power.   

If the READY light does not turn on after 18 hours, the batteries are deeply discharged.  Call 
Technical Support or replace the batteries.

 

A b o u t   t h e   B a t t e ry   Ch a rg e r 

 

Store the charger in a dry area not subject to prolonged below freezing temperatures.   

 

The “intelligent” battery charger monitors the batteries condition and does not overcharge 
the batteries.  It is recommended to leave the battery charger plugged in and charging 
when the MW S is not in use.  Battery life is extended by frequent charging. 

 

The charger’s Green light is on when the battery is finished charging.  Leaving the charger 
plugged in prevents the battery from self-discharging. 

 

The MW S Battery Status LEDs provide the most accurate indication of battery status. While 
the 24VDC charger has Percentage LEDS that also show battery status, use the three 
Battery Status LEDS on the Power Panel. 

 

 

 

MW S P ow er Sw i tch 

 

Содержание Mobile Work Station (MWS) Monarch 9876





















Отзывы: