manualshive.com logo in svg

AVANT 400 Series, Руководство оператора, Страница: 37 / 40

Поделиться
Скачать
AVANT 400 Series Скачать руководство пользователя страница 37

  

37

400 Series

Troubleshooting

Problem

Possible cause

Remedy

Engine does not crank

Main switch off

Turn on the main switch

Battery discharged, battery voltage 
too low

Check and charge

Blown fuse

Check fuses. If fuse blows again, find out the cause. 
Contact service

Battery cables poorly connected

Check battery cables and posts, clean and retighten if 
necessary

Engine cranks but does not start, or 
starts and stops immediately

No fuel or wrong type of fuel

Fill the tank with correct type of fuel. 

Engine does not get fuel, clogged fuel 
filter or fuel line

Fill the tank with correct type of fuel. 

Make sure that the fuel hoses and fuel filter are clean and 
have not been frozen. Replace fuel filter, clean fuel lines.

Cold ambient temperature

Hold ignition key in glow position for longer period. 
If glow indicator lamp is lit, allow it to turn off before 
starting. Extend starting time up to 5 seconds. (Diesel)
Use correct type of engine oil

Auxiliary hydraulics control lever is in 
locking position.

Turn the lever in center (neutral) position.

Battery discharged or damaged.

Jump start with another battery (See page 34), then 
charge the battery or replace if damaged

Engine overheats

Clogged radiator

Clean radiator and fan from engine side

Coolant level low

Add coolant

Leaking cooling system

Check coolant pressure reservoir cap for tightness. 
Check cooling system and all hoses and connections.

Hydraulic system overheats

Hydraulic oil level low

Check and refill, see page 30

Clogged oil cooler

Clean cooler and fan

Fan faulty

Check and clean, repair if necessary

Hydraulic oil flow restricted

Make sure auxiliary hydraulics valve is completely opened 
when using high flow attachments. Adjust lever locking 
plate if necessary.

Hydraulic system overloaded

Use attachment at lower engine rpm,  use with 1-pump 
setting, check attachment for faults. 

The loader does not move even 
after the parking brake has been 
released.

The pins of the parking brake 
mechanism have not locked properly in 
the wheels.

Drive slowly forward or backward in order to lock the 
parking brake.

Parking brake engages the front wheels.

When releasing the parking brake do this in opposite 
order. If the machine must stay in a slope, park it so that 
the heavier end is on downhill side.

Troubleshooting

Содержание 400 Series









































Отзывы:

Нет отзывов