manualshive.com logo in svg

AVANT 400 Series, Руководство оператора, Страница: 21 / 40

Поделиться
Скачать
AVANT 400 Series Скачать руководство пользователя страница 21

  

21

400 Series

Operating instructions

Starting the engine

Before starting the engine do the daily checks, see page 27. Adjust the seat and mirrors (if fitted) so that you have a good 
working position and unrestricted field of vision from the driver’s seat.  Check that all controls function correctly.  See 
to it that the operating area is safe. Read and follow operating and safety instructions.

Stopping the engine (Safe stopping procedure)

1. Lower the boom completely down. Place attachment firmly on the ground, engage parking brake, stop the attachment 

(move auxiliary hydraulics control lever to neutral position, see page 23), set engine revs to idle.

2. Stop the engine by turning the ignition key to the OFF position (to the left)
3. Release auxiliary hydraulics pressure (see page 15).
4. Prevent unauthorized use of the loader. Take off the ignition switch and turn the power off with the battery disconnect switch.

Stop the engine as soon as possible, if any of the following symptoms is observed. Find out the cause before restarting.
•  The oil pressure warning  light turns on during operation.
•  A sudden and unusual noise is heard
•  The colour of the exhaust fumes suddenly darkens or turns white.

1. Turn the battery disconnect switch to ON
2. Move the hand throttle lever         to approximately ¼ throttle
3. Make sure that auxiliary hydraulics is switched off (lever in neutral 

position). Do not press on the drive pedals.

4. Turn the ignition key        to the right until the glow plug 
  indicator light         turns on. 
5. After the glow plug indicator light turns of turn the ignition 
  key further to the right until the engine starts.

2

1

2

1

Do not actuate the starter for more than 10 seconds at a time. If the engine does not start, wait for one minute before 
repeating attempt. If the engine does not start after a few attempts, or runs poorly, see troubleshooting on page 37 and 
the engine owner’s manual.

If auxiliary hydraulics is switched on during starting and there is a hydraulically operated attachment on the 
machine, the attachment can move suddenly and cause a dangerous situation. Make sure that the auxiliary 
hydraulics control lever is in neutral position during starting.

The engine cannot start if auxiliary hydraulics control lever  (no. 7, page 15) is in locking position

Содержание 400 Series









































Отзывы:

Нет отзывов