AVANT 400 Series Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 40

AVANT 400 Series Скачать руководство пользователя страница 16

16

400 Series

Dashboard

On the dashoard on the right side of the driver’s
seat are mounted gauges, indicators and switches
which help the operator to control the loader.

Operating instructions

Controls in the footwell

Following picture shows the controls located in the footwell

2

1

19

15

16

17

10

7

2

4

5

11

12

14

13

2. Headlamp indicator (Road traffic light kit)

4. Seat heater indicator

5. Glow plug indicator

6. Fuel gauge

7. Work light switch

10. Oil pressure indicator

11. Charge indicator

12. Thermometer

13. Ignition switch

14. Signal horn

15. Seat heater switch (optional extra)

16. Drive release / anti slip valve switch (optional extra)

17. Boom floating switch (optional extra)

19. Worklight indicator

1. Drive pedal, left:

drive backward

2. Drive pedal, right:

drive forward

3. Parking/emergency brake handle

  •  locking: pull the handle and turn down into
    locking position
  • releasing: turn up and let the handle go down

Parking brake locks mechanically - spring-
loaded pins go into the holes of the
parking brake drum on the front wheels.
Make sure that the brake locks properly
by driving a bit forward or backward.

4. Hour meter

See correct operation of drive pedals on page 22.

3

4

6

«
...
14
15
16
17
18
...
»

Содержание 400 Series









































Отзывы:

Нет отзывов