AVANT 400 Series Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 40

AVANT 400 Series Скачать руководство пользователя страница 24

24

400 Series

Operating instructions

Requirements for attachments

• Read Operators Manual of the attachment before starting operation. Make sure that the attachment is

compatible with the loader. Contact your Avant dealer if necessary

• Check max. allowed hydraulic oil flow for the attachment. Adjust engine revs so that they are suitable

for the work and the attachment.

• Make sure that the attachment is connected properly on the attachment coupling plate, and that it is

being used in accordance with the instructions in the Operators Manual. Follow instructions regarding
personal protective equipment and safety distances.

• Put the attachment down on the ground and stop the engine before leaving driver’s seat. Familiarise

yourself with the operation and stopping of the attachment at a safe place. Follow service instructions.

Coupling the attachments

Coupling of the attachments into the attachment coupling plate happens as follows:

Stage 1 :

• Lift up the two locking pins on both sides of the attachment coupling plate

and turn them backward so that they remain in the up position

• Make sure that the pins remain in the up position, otherwise you cannot

couple the attachment properly!

Stage 2 :

•  Turn the attachment coupling plate with the tilt movement so
  that the upper edge of the plate leans forward.
•  Drive the loader into the attachment

Stage 3 :

•  Lift the boom a little so that the attachment lifts off of the ground
•  Pull the boom control lever to the left so that the lower edge
  of the attachment coupling plate turns into the attachment

Stage 4 :

• Lock the lockin pins manually or use the hydraulic locking.
• Some attachments can be locked using the automatic return of the locking

pins. See operator’s manual of the attachment. If recommended, pull the boom
control lever more to the left so that attachment coupling plate turns more and
the brackets on the boom push the pins down in the holes of the attachment.

• Always make sure that the pins lock properly down in the holes of the attachment!

«
...
22
23
24
25
26
...
»

Содержание 400 Series









































Отзывы:

Нет отзывов