Avalon Gourmet Скачать руководство пользователя страница 22

Страница: 22 / 47

www.avalonbrewer.com

(800)561-6162

AVALON Gourmet Révision A

AVALON

Gourmet

INSTALLATION MANUAL

3.13

Filter Paper Installation

Make sure the power of the
brewer is turned ON;

Place the filter paper roll on the
support bracket so that it
dispenses on the left hand side;
(See the diagram inside the
brewer)

Toggle the brewer paper switch
ON (SW4 on the main board, see
page 22), the brew chamber will
lift up;

Note: the brew chamber will
not lift up if the switch does
not sense any filter paper

Pass it under the left guide
bracket of the brew group, under
the brew chamber and under the
wheel guides by gently lifting
them using the yoke;

Pull on the paper and carry it
through the cabinet chute hole
and into the waste bin;

Make sure that it is feeding
straight. Verify that it stays within
the first guide. Improper filter
paper feeding will cause a
vacuum leak and may cause
grounds to spill inside the
equipment.

Toggle the brewer paper switch
back to OFF (SW4 on the main
board);

The filter paper will advance while
the brewer assembly cycles and
the brew chamber will settle down
on the paper, ready for the
next cup.

Initial Setup

Guide
bracket

Yoke

Содержание Gourmet
















































Результаты поиска

Содержание Gourmet

Отзывы:

Похожие инструкции для Gourmet

Бренды по названию

Популярные бренды

Avalon Gourmet, Руководство по установке

Результаты поиска

Содержание Gourmet

Отзывы:

Похожие инструкции для Gourmet

Бренды по названию

Популярные бренды