background image

AS-2510 TW 

Installation Guide  

P. 19

 Diagnostics – Parking Light Flash Table 

Flashes 

Description 

1

x

Doors locked, Starter Kill armed. 

x

End of Run Time. 

x

TRUNK

 button pressed 

x

Start signal received by the Remote Car Starter. 

x

Cold Weather Mode cancelled. 

x

Cannot start after maximum number of attempts is reached. 

2

x

Doors unlocked, Starter Kill disarmed. 

x

Run time cancelled. 

x

Exit Remote Valet.  

x

Remote start attempt cancelled by remote. 

3

x

Entering 

Cold Weather Mode

.

x

Entering Remote Valet. 

4

x

+12 V where detected on the brake line and cranking was cancelled. 

x

Entering Tach-programming Mode 

5

x

New Transmitter programmed. 

x

Tach programmed. 

6

x

A remote start was attempted while a Tach or a vacuum signal was detected 
before cranking. 

8

x

Unit reset: occurs when the Unit is reset to the factory defaults. 

10

x

The Hood Switch line went to ground during cranking or Run Time. 

1 – pause – 2 

x

There was an attempt to start the vehicle while the Remote Car Starter was 
in Valet Mode. 

ON solid 

x

Cold Weather Mode

: the Brake Pedal is being held down. 

2 – pause – 2 

x

There was an attempt to start the vehicle while the Remote Car Starter was 
in Home Valet Mode. 

ON 2 sec. 

x

The Hood is up and the Hood Switch line went to ground. This is step one of 
the Programming Centre procedure. 

ON 3 sec. 

x

First press of the 

START

 button under Safe Start. 

ON 4 sec. 

x

Locking or unlocking a Door (with Door pulses configured to 4 sec.) 

ON 25 sec. 

x

The Hood Pin-switch has been pressed twice: the Unit went into step 1 of the 
Programming Centre procedure, and no Transmitter activity was detected for 
20 seconds. 

x

Or

the Unit went into step 1 of the Transmitter Programming procedure and 

no activity was detected for a few seconds. The Unit has exited the 
Transmitter Programming procedure.

Irregular

x

If the unit gives irregular signals (1 to 10 flashes followed by a pause, 
followed by further flashes), the system is playing back Start Failure Codes. 
This occurs when the Hood Pin-switch is pressed three times. 

Constant

flashes 

up to 30 sec. 

x

Panic Mode triggered. 

Содержание AS-2510 TW




















Отзывы: