background image

24

7. MAINTENANCE

Your wind turbine has been designed to run for long periods without requir-
ing any maintenance. 
The performance will be enhanced if you periodically inspect your system.
Review the following simple maintenance procedures and implement them
every six months.

Caution: Do not go near the wind turbine during operation.
The blades are sharp. Please handle it with care.

•  Check blades for superficial damage, replace the blades if damaged. 
   It is important to not use blades that are damaged, as you will lose overall 
   balance, resulting in a decrease inefficiency. Should you notice damage to 
    the blades you must replace all 3, these blades are balanced as sets.
•  Check the blade bolts and the hub nut for tightness.
•  Check nosecone for cracks and tighten nuts.
•  Wipe any excess dirt build-up from the blades.
•  Check all electrical connections to make sure they are tight and free from corrosion.
•  Check the voltage of your battery bank with a Multi-meter and clean the terminals.
•  We suggest replacing the blades every five years for optimal performance.

Please Note: Apply the Manual Brake to safeguard your unit in the 
mention below situation.

•  Bad weather and strong wind
•  Maintenance & replacement work
•  MPPT failure/ no sign
•  Free spinning
•  Battery pack disconnected
•  Broken Blades
•  Mechanical noise
•  Notice anything abnormal

Содержание 1500 Watts Wind Turbine

















































Отзывы:

Похожие инструкции для 1500 Watts Wind Turbine