Automatic Solutions CTR50 Скачать руководство пользователя страница 4

Страница: 4 / 22

HANGING GATES

Decide on a position for the hinges on your gates. Try to keep the hinges close to the top and bottom of your gate as this will put them in

best position structurally. When you have decided the position mark the spots on your posts allowing for the clearance gap under your

gates. Using the Tek screws supplied fix the large part of the hinge to the post. Be careful not to use high torque settings that strip the Tek

screw when tightening. If you do you will need to either move the position or change the fastener.

When all of your post hinges are fitted you are ready to hang your gates. There are a number of ways to do this. If you are very accurate

you can measure and mark your gate, fit the hinge bracket to the gate and then assemble all the parts. You might find it easier however to

assemble the hinge so it is complete on the post, use blocks under your gate to lift and hold it at the correct height and then fix the hinges

to the gate. Using this method you can also use a 30mm packer to get your gap between post and hinge accurate. Once both gates are

hung you can then adjust the hinges for gap and height.

INSTALLATION OF STOPS

We have provided a centre stop and two open stops which must be installed for your automation to function correctly. They are designed

to be bolted down but may be concreted in place by simply welding a short 250mm length of steel with a cross brace to the base.

Содержание CTR50























Результаты поиска

Содержание CTR50

Отзывы:

Бренды по названию

Популярные бренды

Automatic Solutions CTR50, Руководство по установке

Результаты поиска

Содержание CTR50

Отзывы:

Бренды по названию

Популярные бренды