Automatic Solutions CTR50 страница 18 Скачать руководство пользователя

Страница: 18 / 22

Terminal board J5

Terminal1 – Aerial cable connection (shield) for radio receiver card

Terminal2 – Aerial cable connection (signal) for radio receiver card

Terminal board J1

Terminal1 - Power supply positive for photo-cells or other devices

Terminal2 - Power supply negative for photo-cells or other devices (common)

Terminal3 - Power supply positive for blinker

Terminal4 - Power supply negative for blinker (common)

Terminal5 - Motor M1 power supply

Terminal6 - Motor M1 power supply

Terminal7 - Motor M2 power supply

Terminal8 - Motor M2 power supply

Terminal9 – Power supply positive for electric lock

Terminal10 – Power supply negative for electric lock (common)

Terminal board J3

Terminal1 - Motor 1 opening Limit switch normally closed electric contact

Terminal2 - Motor 1 closing Limit switch normally closed electric contact

Terminal3 - Motor 1 Encoder signal input

Terminal4 - Common terminal for Motor 1 Limit switches and Encoder

Terminal5 - Motor 2 opening Limit switch normally closed electric contact

Terminal6 - Motor 2 closing Limit switch normally closed electric contact

Terminal7 - Motor 2 Encoder signal input

Terminal8 - Common terminal for Motor 2 Limit switches and Encoder

Important: The equipment only accepts a “TTL” or “OPEN COLLECTOR” input as Encoder signal.

TTL

OPEN COLLECTOR

FS1 Faston – Backup battery’s positive pole connection

FS2 Faston – Backup battery’s negative pole connection

FS3 Faston – 12/15/20 Vac power supply from the electric transformer

FS4 Faston – 12/15/20 Vac power supply from the electric transformer

CTR50 - Connection of the devices

Motor 1 – Terminals 5 and 6 on J1

Motor 2 – Terminals 7 and 8 on J1

Blinker – Terminals 3 and 4 on J1

Electric lock – Terminals 9 and 10 on J1

Photo-cells power supply – Terminals 1 and 2 on J1

NC photo-cell contact – Terminals 4 and 6 on J2

NC stop push-button – Terminals 4 and 5 on J2

NC photostop contact – Terminals 7 and 8 on J2

NO start push-button – Terminals 1 and 3 on J2

NO pedestrian start push-button – Terminals 1 and 2 on J2

Aerial – Terminals 1 and 2 on J5

Open gate lamp - Terminals 9 e 10 on J1

NC Motor 1 opening limit switch contact – Terminals 1 and 4 on J3

NC Motor 1 closing limit switch contact – Terminals 2 and 4 on J3

NC Motor 2 opening limit switch contact – Terminals 5 and 8 on J3

NC Motor 2 closing limit switch contact – Terminals 6 and 8 on J3

Motor 1 Encoder connection - Terminals 3 and 4 on J3

Motor 2 Encoder connections - Terminals 7 and 8 on J3

IMPORTANT:

If no cable is connected to the FC1A and FC1C inputs, the control of Motor 1 limit switches will be automatically disabled.

If no cable is connected to the FC2A and FC2C inputs, the control of Motor 2 limit switches will be automatically disabled.

Содержание CTR50























Результаты поиска

Содержание CTR50

Отзывы:

Похожие инструкции для CTR50

Бренды по названию

Популярные бренды

Automatic Solutions CTR50, Руководство по установке

Результаты поиска

Содержание CTR50

Отзывы:

Похожие инструкции для CTR50

Бренды по названию

Популярные бренды