Automatic Solutions CTR50 страница 16 Скачать руководство пользователя

Страница: 16 / 22

In any operation mode, the safety devices cause the following effects:

Stop:

If the stop command is enabled no cycles can start and the start command will have no effect. If a stop command is supplied

during motion, the gate will immediately stop and interrupt its operating cycle. This condition will continue while the stop command is on. A

start command following a stop command always determines an opening cycle. A stop command supplied during the pause period

interrupts the operating cycle. A start command subsequently supplied will start a closure cycle.

Photo-Cell:

This device has effect only during the closure phase or in the pause period. If an obstacle covers the photo-cell during the

closure phase, the gate stops and reverses its motion after approx. 1.5 sec. If an obstacle covers the photo-cell during the pause period

the pause time is reset and the automatic closure is therefore delayed.

Photostop:

If an obstacle covers the photo-cell during the gate’s motion (opening or closure), or during the period preceding the operating

cycle’s start, then the gate is temporarily stopped, until the obstacle is removed. When the obstacle is removed and the photocell is freed,

an opening cycle will start. This does not apply when a start command determines the closing phase in step-by-step mode at the end of an

opening cycle. If an obstacle covers the photostop during the pause period the pause time is reset and the automatic closure is therefore

delayed.

Pedestrian start:

The pedestrian start command operates in the same way as the other start command, but in this case only the (M2) wing

fitted with the electric lock will be opened or closed. The pedestrian start command has no effect during a start cycle and up to the end of

the closing phase (closed gate). During a pedestrian start cycle the start command is always active and causes the start of an opening

cycle for both wings.

Содержание CTR50























Результаты поиска

Содержание CTR50

Отзывы:

Похожие инструкции для CTR50

Бренды по названию

Популярные бренды

Automatic Solutions CTR50, Руководство по установке

Результаты поиска

Содержание CTR50

Отзывы:

Похожие инструкции для CTR50

Бренды по названию

Популярные бренды