Automated Logic InterOP8500 Скачать руководство пользователя

Страница: 1 / 20

Automated Logic Corporation

•

1150 Roberts Blvd.

•

Kennesaw, GA 30144

•

770/429-3000

•

770/429-3001 Fax

•

www.automatedlogic.com

•

Automated Logic logo, SuperVision, Eikon, Alert, and InterOp are registered trademarks of Automated Logic
Corporation. WebCTRL is a trademark of Automated Logic Corporation. BACnet

is a registered trademark of ASHRAE.

All other brand and product names are trademarked by their respective companies.

Technical Instructions

InterOP8500

Introduction 2
Specifications 3
Mounting 4

Connecting Expander Modules 4

Addressing 4
Power Wiring 5

Using the ALC Power Supply 6
Using the Johnson Power Supply 7

Network Communications 7
Communicating with the Workstation 8
Input/Output 9

Analog Inputs 9
Unswitched and Switched Inputs 10
Calculating Offset and Gain 12
Binary I/O Power Jumper 12
Binary Inputs 13
Binary Outputs 13

Point Identifiers 15

Point Identifiers in WebCTRL 15
Channel Numbers in SuperVision 15

Transferring Memory 17

Transferring Memory in WebCTRL 17
Transferring Memory in SuperVision 18

Troubleshooting 18

Formatting the Module 18
LEDs 18
Protection 19
Production Date 19

Sample GFB 20

Содержание InterOP8500





















Результаты поиска

Содержание InterOP8500

Отзывы:

Похожие инструкции для InterOP8500

Бренды по названию

Популярные бренды

Automated Logic InterOP8500, Технические инструкции

Результаты поиска

Содержание InterOP8500

Отзывы:

Похожие инструкции для InterOP8500

Бренды по названию

Популярные бренды