Automated Logic InterOP8500 Скачать руководство пользователя страница 3

Страница: 3 / 20

Revised 7/10/01 • InterOP8500

The table below outlines the limitations and
requirements depending on whether you are
using WebCTRL or SuperVision to
communicate with your InterOP8500.

For more information, see the appropriate
module driver document on the Automated
Logic website at www.automatedlogic.com.

Specifications

Power

5VDC, 175mA (external), 275 mA

(internal).

12VDC, 25mA.

12VDC, 175mA (external power), 25 mA
(internal power) supplied through the
card-edge connector.

24VAC, 300mA for use with the large
keypad/display.

Inputs

8 binary inputs, 15 analog inputs

(configurable for 1k ohm nickel RTD or 1
to 5V).

Input Resolution

12 bit A/D.

Digital Outputs

16 digital outputs,

12VDC, 300mA fused output.

Communication

For WebCTRL, 156 kbps

BACnet-over-ARCNET and 9600 bps or
38.4 kbps EIA-485 BACnet MS/TP.

For SuperVision, 156 kbps BACnet-over-
ARCNET, 9600 bps or 38.4 kbps Legacy
CMnet. Access Port:9600 bps or 38.4 kbps
EIA-485.

WebCTRL

SuperVision

Module Driver

DRV_InterO
P8500

85M

Number of Function
Blocks*

100

Number of BACnet
Objects*

2000

1000

* depending on available memory

Figure 2. Network Architecture

Johnson Field
Termination Board

Johnson
Field Device

Johnson I/O Devices

Johnson
Field Device

InterOp8500

CMnet (ARC156)

U-Cards

UNI/32

U-Line: 9600 bps or 38400 bps

TNPB

MX-Line

LGRM-E

MX-Line

S-Line

For WebCTRL, BACnet/IP.
For SuperVision, BACnet/Ethernet.

Содержание InterOP8500





















Результаты поиска

Содержание InterOP8500

Отзывы:

Automated Logic InterOP8500, Технические инструкции, Страница: 3 / 20

Результаты поиска

Содержание InterOP8500

Отзывы: