Automated Logic InterOP8500 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 20

Automated Logic InterOP8500 Скачать руководство пользователя страница 2

Revised 7/10/01 • InterOP8500

2

© 2001 Automated Logic Corporation

Introduction

The InterOP8500 mounts directly to a Johnson
Controls panel, replacing the Johnson FIC-1n1
control board and the PCR-102. The
InterOP8500 uses the same mounting
brackets and can be powered by the existing
power supply (using a special adaptor cable).
However, in order to retain the UL listing, the
RPA-105 and the LPS-105 must be replaced by
the PWRSUP8500.

In addition, the InterOP8500 uses the Johnson
field termination board (FTB-102) for binary
I/O and analog input. Please note that slave
FICs must be replaced by separate, stand-
alone InterOP8500 modules.

The InterOP8500’s edge connector plugs
directly into the field termination board’s
socket. Once connected, the InterOp8500
accesses the binary and analog I/O, as well

as an isolated 12VDC power supply for its
binary outputs. The InterOP8500 board
contains the microprocessor, a connection
port for the network connection, and a port
for I/O expansion. The InterOP8500 has 8
binary inputs, 15 analog inputs (which can be
set to either RTD or voltage mode), and 16
digital outputs.

The Access Port allows communication with
WebCTRL or SuperVision. The InterOP8500's
keypad port provides the interface for serial
communications with a BACview

1

or

BACview

2

keypad display. Refer to the

BACview

1

or

BACview

2

Hardware Technical

Instructions

for more information on small

and large keypad display.

NOTE

NOTE

NOTE

NOTE A 24VAC power supply is required for
a keypad.

Figure 1. InterOP8500 layout and dimensions

CMnet
Terminal

Power

Switch

Power

Terminals

Baud Rate

Switch

Dual Rotary

Address

Analog Inputs

Binary I/O

11 1/4"

28.58 cm

8 5/8"

21.9 cm

5/8"

1.59 cm

3/8"

.95 cm

2/8"

.64 cm

4 7/8"

12.38 cm

1"

2.5 cm

Binary Output

HOA Switches

Binary I/O

Power Jumper

Format

Button

10's

1's

Access

Port

Comm Mode

Jumper

Expander Port

InterOp8500

Keypad Port

Keypad

Power

Binary Outputs

«
1
2
3
4
...
»

Содержание InterOP8500





















Отзывы:

Нет отзывов