Automated Logic InterOP8500 Скачать руководство пользователя | Manualshive

Страница: 6 / 20

background image

Revised 7/10/01 • InterOP8500

6

© 2001 Automated Logic Corporation

Using the ALC Power Supply

The PWRSUP8500 power supply replaces both
the Johnson Controls LPS-105 and Johnson
RPA-105. The PWRSUP8500 is designed to fit
into the previous power supply's mounting
bracket and power the InterOP8500. The
PWRSUP8500 does not require any adaptor
cables. It connects directly to the
InterOp8500's power connector.

CAUTION

CAUTION

CAUTION

CAUTION The PWRSUP8500 module is a
120VAC device. Take appropriate isolation
measures when mounting a PWRSUP8500.

1. Turn the power switches off on the

InterOP8500 and the Johnson Controls
panel.

2. Unplug the LPS-105 from the power outlet

(see Figure 5).

3. Remove the power cable from the

InterOP8500 power connector.

4. Take out the mounting screw from the

face of the LPS-105 and remove the LPS-
105 from the Johnson Controls panel.

5. Take out the mounting screw from the

back of the RPA-105 and remove the RPA-
105 from the Johnson Controls panel.

6. Place the PWRSUP8500 in the same

brackets that the RPA-105 was in. Make
sure the edges of the PWRSUP8500 are in
the slots.

7. Replace the mounting screw in the back

of the PWRSUP8500 (see Figure 3 on page
5).

8. Connect the power cable of the

PWRSUP8500 to the InterOP8500 power
connector and plug the PWRSUP8500 into
the power outlet.

9. After verifying that you have +5V on the

red and +12V on the blue, referenced to
the Gnd (black), turn the InterOp8500
power switch on.

Figure 5. InterOp8500/RPA-105 and LPS-105 mounted in Johnson Controls panel

ON
OFF

Johnson Controls
Panel

Johnson Field
Termination Board
(FTB-102)

InterOp-8500

RPA-105
(side-mounted)

Plastic Retainers

Power Adapter
Cable

Grounding Wire
(green)

Edge Connectors

LPS-105

Panel Power
Switch

J23

J20

to External
Power Supply

«
...
4
5
6
7
8
...
»

Содержание InterOP8500





















Отзывы:

Нет отзывов

Похожие инструкции для InterOP8500

Бренд: National Instruments Страницы: 102

Бренд: NAU ROBOTICS Страницы: 109

Maschine Mikro MK2

Бренд: Native Instruments Страницы: 181

Бренд: X Rocker Страницы: 38

Бренд: Voltech Страницы: 8

traxon e:cue LCE-mx

Бренд: Osram Страницы: 35

Бренд: National Instruments Страницы: 14

Бренд: Maximum Controls Страницы: 58

phyCORE-MCF548x

Бренд: Phytec Страницы: 104

Бренд: Aurora Страницы: 2

Бренд: GSD Страницы: 5

Бренд: AC Tech Страницы: 2

Бренд: V-TAC Страницы: 2

Бренд: Diamond Systems Страницы: 15

Бренд: Raypak Страницы: 2

Бренд: 4D systems Страницы: 6

Бренд: Phoenic Mecano Страницы: 5

Бренд: Variotech Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды