Automate Raptor TC-1417 Скачать руководство пользователя

Страница: 2 / 32

Thank You For Your Order!

Congratulations on your purchase of an AutoMate CNC Lathe. With proper setup and care, your

machine will provide many years of quality work and productivity.

This guide covers general instructions for setup and maintenance for the Automate CNC Lathe. In
addition to this guide you will also receive a machining operations and programming handbook

for the Siemens 808D control system. We strongly recommend keeping this setup guide with the
manual when your machine arrives.

Enjoy your new CNC Lathe!

This manual is specifically written for the

RAPTOR TC-1417 CNC LATHE

Detroit Machine Tools

170 Aprill Drive

Ann Arbor, MI

48103

For additional assistance or information,

you may contact us by

Phone: 800-476-4849

Fax: 800-431-8892

Email:

Содержание Raptor TC-1417

































Результаты поиска

Содержание Raptor TC-1417

Отзывы:

Похожие инструкции для Raptor TC-1417

Бренды по названию

Популярные бренды

Automate Raptor TC-1417, Руководство пользователя

Результаты поиска

Содержание Raptor TC-1417

Отзывы:

Похожие инструкции для Raptor TC-1417

Бренды по названию

Популярные бренды