Auto Crane HC-5 NEXSTAR Скачать руководство пользователя страница 36

Страница: 36 / 88

NexStar Troubleshooting

HC-7X NEXSTAR

NexStar Error Code Table

INFO BOX

CAUSE

EFFECT

SOLUTION

DIRTY FILTER

Filter is dirty if oil

temperature is at least

100 °F

Operates normally.

Replace filter. Auto Crane part number is

366823910.

ADDRESS TAG

ERROR

Crane does not

recognize address tag

All outputs are disabled. Check connection at address tag. Check for

water in connection. Dry out if necessary.

AUTOSTOW

ACTIVE

Crane is currently in

auto stow mode

Crane will move into

preset stow position

while trigger is active.

Selecting any function will disengage auto stow

mode.

PERSONNEL

BASKET ACTIVE

Crane is currently

in personnel basket

mode

Disables hoist functions

and remaining functions

by 50%.

Disengage through mode selection screen.

Reference NexStar Operations section for more

detail.

STABILITY TEST

EXCEEDED

Number of operations

in stability test mode

has exceeded limit

Disables stability test

mode.

If stability test mode is required, please contact

Auto Crane technical support.

OIL TEMP

WARNING

Oil temperature has

exceeded 180 °F (if

applicable)

Normal Operation.

Disengage PTO to allow oil to cool. If problem

persists, add oil cooler to hydraulic system.

OIL TEMP

ALARM

Oil temperature has

exceeded 200 °F (if

applicable)

Normal Operation.

Disengage PTO to allow oil to cool. If problem

persists, add oil cooler to hydraulic system.

ZONE A ACTIVE

Crane is currently

located in Zone A base

on stability chart (if

applicable)

Overload based on Zone

A load chart.

Reference stability chart for zone locations.

Reference load chart for crane capacities in that

zone.

ZONE B ACTIVE Crane is currently

located in Zone B base

on stability chart (if

applicable)

Overload based on Zone

B load chart.

Reference stability chart for zone locations.

Reference load chart for crane capacities in that

zone.

CW ROT INTO

Crane wint into

overload while rotating

clockwise from

Zone A to Zone B (if

applicable)

Disables clockwise

rotation, boom down,

and hoist up.

Rotate counter-clockwise to return to Zone A or

reduce load to clear alarm.

Содержание HC-5 NEXSTAR

























































































Результаты поиска

Содержание HC-5 NEXSTAR

Отзывы:

Auto Crane HC-5 NEXSTAR, Руководство пользователя, Страница: 36 / 88

Результаты поиска

Содержание HC-5 NEXSTAR

Отзывы: