Auto Crane HC-5 NEXSTAR Скачать руководство пользователя страница 34

Страница: 34 / 88

NexStar Troubleshooting

HC-7X NEXSTAR

NexStar Remote Troubleshooting Table

PROBLEM

POSSIBLE REASON

ACTION

Remote control will not turn on

Remote control Emergency Stop

switch is engaged.

Ensure the Emergency Stop

switch is pulled out.

Internal battery has discharged

below operating level.

Attach backup alkaline battery

pack or tether cable. Allow time

for internal battery to charge

(approx. 15 minutes) then cycle

power.

Remote control will not

communicate with the base

station

Incorrect system RF channel.

Ensure the remote control and

the base station are set to the

same RF channel by synching

the remote to the base station.

System out of range.

Ensure the startup procedure

is initiated within 100 feet of

the receiver. Ensure the signal

strength indicator level is greater

than one bar.

Remote control will not respond

with base station when tethered

System not in tether mode.

Ensure the remote is started

up and initiated with the tether

cable attached.

The tether cable or connectors

are damaged

Inspect the tether cable and/or

connectors for damage.

Remote control will not turn on

in tether mode.

Remote control Emergency Stop

switch is engaged.

Ensure the Emergency Stop

switch is pulled.

The connecting tether cable

is not installed, installed

improperly, or is damaged.

Ensure the tether cable is

installed and secured correctly.

Inspect the tether cable and

connectors for damage.

Remote control is failing switch

scan.

Ensure all switches, buttons, and

joysticks are in the off position.

Remote control will not

communicate with the base

station in wireless mode

System not in wireless mode.

Ensure that the startup

procedure is initiated withing

100 feet from the base station.

Ensure the signal strength

indicator is greater than one bar.

Содержание HC-5 NEXSTAR

























































































Результаты поиска

Содержание HC-5 NEXSTAR

Отзывы:

Auto Crane HC-5 NEXSTAR, Руководство пользователя, Страница: 34 / 88

Результаты поиска

Содержание HC-5 NEXSTAR

Отзывы: