background image

S P E C I F I C AT I O N S

F R E QU E N C Y   R E S P O N S E  

20Hz - 20kHz (+0,-3dB)

TOTA L   H A R M O N I C   D I S TO RT I O N  

< 0.1% @ 1kHz

S I G N A L   TO   N O I S E   R AT I O

> 90dB (all pots at centre position)

C R O S S TA L K

>70dB

TO N E   C O N T R O L S  

B A S S   @   1 0 0 H Z

+/- 12dB

T R E B L E   @   1 0 K H Z

+/- 12dB

S E N S I T I V I T Y  

Mic Sens 4.36mV, -45dBu Imp 1k3ohm

( Tr i m   i n   c e n t re   0 d B )

Line Sens 0.775V, 0dBu Imp >100k

RCA 200mV, -12dBu Imp 30kohm

M A X   L E V E L   I N

XLR mic -15dBu line +30dBu

RCA >30dBu

M A X   L E V E L   O U T  

+21dBu

P H A N TO M   P OW E R  

15V DC

O U T P U T S  

M A S T E R   O U T

Nominal Level 0dBu into 1kohm

Imp 100ohm

M O N O   H E A D P H O N E   O U T

Nom -6dB into 200ohm

Imp 10ohm

M O N O   R E C   O U T

Nom -12dB into 10kohm

Imp 10kohm

P OW E R   I N P U T  

AC: 230V/50Hz or 115V/60Hz, 

3 pin IEC320-C14 connector;

DC: 24 Volts via 2.1mmx5.5mm DC socket

P OW E R   C O N S U M P T I O N   ( M A X )

7 VA

F U S E S

M A I N S   ( 1 1 5 V )

120mA

M A I N S   ( 2 3 0 V )

63mA

D I M E N S I O N S   h   x   w   x   d

44mm x 482mm x 182mm

(1.75“x19”x7.2”)

S H I P P I N G   D I M E N S I O N S   h   x   w   x   d

90mm x 505mm x 270mm 

(3.5“x19.9”x10.6”)

W E I G H T

N E T

2.75kg (6.1lb)

S H I P P I N G

3.75kg (8.3lb)

M X 8 1   I N S TA L L AT I O N   &   O P E R AT I O N   M A N UA L

PAG E   1 1

Содержание MX81













Отзывы: