AussieCarHoists YL-250 страница 37 Скачать руководство пользователя

Страница: 37 / 47

YL-250 5000KG 2 BASE PLATE CAR HOIST

Installation and operation manual

WILL NOT RAISE LOADED LIFT

POSSIBLE CAUSE

1. Air in oil, (1,2,3)
2. Cylinder binding, (4)
3. Cylinder leaks internally, (4)
4. Lift overloaded, (5,4)

5. Lowering valve leaks, (6,7,1,4,8)

6. Motor runs backwards, (9,11,8

7. Pump damaged, (4,8)

8. Pump won’t prime, (1,2,3,4,10,8)

9. Relief valve leaks, (7,4,8)

10. Voltage to motor incorrect, (9,11,4)

REMEDY INSTRUCTION

Check oil level

The oil level should be up to the bleed screw in the reservoir with the lift all the way down.

Check/tighten inlet tubes

Replace inlet hose assembly.

Oil seal damaged

Replace oil seal and install.

See installation manual

Contact Customer Support.

Check vehicle weight

Compare weight of vehicle to weight limit of the lift.

Flush release valve

Hold release handle down and start unit allowing it to run for 15 seconds.

Replace with new part

Replace with new part.

Return unit for repair

Return unit for repair.

Check motor is wired correctly

Compare wiring of motor to electrical diagram on power unit drawing.

10.

Inlet screen clogged

Clean inlet screen or replace.

11.

Check wall outlet voltage and wiring

Make sure unit and wall outlet is wired properly.

IMPORTANT

If after observing that all mechanical locks are released and the lift still fails after following all standard operating procedures,
immediately stop using the lift and contact factory or factory approved service center for further instructions.

LIFT WILL NOT STAY UP

POSSIBLE CAUSE

1. Air in oil, (1,2,3)
2. Check valve leaks, (6)

3. Cylinders leak internally, (7)

4. Lowering valve leaks, (4,5,1,7,6)

5. Leaking fittings, (8)

REMEDY INSTRUCTION

Check oil level

The oil level should be up to the bleed screw in the reservoir with the lift all the way down.

Oil seal damaged

Replace oil seal around pump shaft.

Bleed cylinder

Refer to Installation Manual.

Flush release valve

Hold release handle down and start unit allowing it to run for 15 seconds.

Replace with new valve

Replace with new valve.

Return unit for repair

Return unit for repair.

See Installation Manual

Contact Customer Support.

Check complete hydraulic system for leaks

Tighten all hydraulics fittings and inspects all hoses.

HIGH-LIFT

Содержание YL-250
















































Результаты поиска

Содержание YL-250

Отзывы:

Похожие инструкции для YL-250

Бренды по названию

Популярные бренды

AussieCarHoists YL-250, Инструкция по установке и эксплуатации

Результаты поиска

Содержание YL-250

Отзывы:

Похожие инструкции для YL-250

Бренды по названию

Популярные бренды