AussieCarHoists YL-250 страница 14 Скачать руководство пользователя | Manualshive

Страница: 14 / 47

background image

YL-250 5000KG 2 BASE PLATE CAR HOIST

Installation and operation manual

14

SPECIFICATIONS OF CONCRETE

IMPORTANT NOTICE

Concrete must be in compliance to the specifications below.

Failure To Do So May Result In Personal Injury or Property Damage.

1. Concrete must have a thickness of 6.3 inches minimum and without reinforcing steel bars, and must be completely cured before lift installation.
2. Concrete must be in good condition and must have a test strength 3,000 psi (210kg/cm²) minimum.
3. Floors must be level and no cracks

POWER SUPPLY

The capacity of power must be 3HP minimum. The electrical wire must be a minimum of 10 gauge.

INSTALLATION

1. Location of Installation

Check the installation location (concrete, layout, space size etc.) so it is suitable for lift installation.

LIFT HEIGHT CLEARANCE NOTE:

There must be 70” plus the height of typical vehicle MIN distance from top of lift to nearest obstruction

2. Use a carpenter’s chalk line to establish installation layout of base plate.

3.

Using the base plate on the

POWER SIDE

post as a guide, drill each anchor hole in the concrete approximately 4.72” deep using a rotary

hammer drill and 0.79” concrete drill-bit. To ensure full holding power, do not ream the hole or allow the drill to wobble.

4.

After drilling, remove dust thoroughly from each holemaking certain that the posts remain aligned with the chalk line.

DANGER

HIGH-LIFT

«
...
12
13
14
15
16
...
»

Содержание YL-250
















































Отзывы:

Нет отзывов

Похожие инструкции для YL-250

Бренд: TBEI Страницы: 22

Бренд: Black Bull Страницы: 4

BRADEN Gearmatic BG6A

Бренд: Paccar Winch Страницы: 35

trifor/griphoist T-508D

Бренд: Tractel Страницы: 36

Бренд: Tractel Страницы: 36

tralift TT 1000

Бренд: Tractel Страницы: 70

Бренд: Ribimex Страницы: 24

Ribitech PE100/200PT

Бренд: Ribimex Страницы: 28

Бренд: Euro Shatal Страницы: 5

Бренд: Beta Max Страницы: 139

Бренд: Yale Страницы: 31

Бренд: Nitchi Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды