background image

13

Connecting/Disconnecting the Gas

Using Gas

Carbon Monoxide Hazard

•  This appliance can produce carbon monoxide which has no odor. Using it in an enclosed space can kill you.
•  Never use this appliance indoors, on recreational vehicles, or boats.

DA N G E R

!

To reduce the risk of serious bodily injury or death from fire or explosion:
• Use only propane gas with this LP gas grill.
• Do not attempt to convert an LP unit to natural gas.
• Always use a gas appliance outdoors in an open area with good ventilation to avoid breathing toxic fumes from 

leaking gas, explosion, or fire. As with all conventional fuels, the burning process consumes oxygen and produces 
toxic gases, including carbon monoxide. In addition, the combustion products of such fuels, including liquefied pe-
troleum (LP), contain chemicals known to the state of California and other authorities to cause cancer, birth defects, 
and other reproductive harm.

WARNING

!

To reduce the risk of serious bodily injury from fire or 

explosion:

•  Read and follow all warnings on LP Gas Cylinder.
•  Do not operate the LP gas grill without the LP Gas Cylin-

der secured to the cart and oriented as shown in Assem-
bly Instructions for Connecting the LP Gas Cylinder.

•  Never connect or disconnect LP Gas Cylinder or fittings 

while grill is in use or is hot.

•  When the LP Gas Cylinder is connected, keep the grill 

outside in a well-ventilated space.

•  Do not use an LP Gas Cylinder if it shows signs of dents, 

gouges, bulges, fire damage, corrosion, leakage, exces-
sive rust, or other forms of visual external damage; it 
may be hazardous and should be checked by a liquid 
propane supplier. Do not use an LP Gas Cylinder with a 
damaged valve.

•  Do not store a spare LP Gas Cylinder under or near the 

LP gas grill.

•  When grill is not in use, turn off all grill Control Knobs, LP 

Gas Cylinder valve and disconnect LP Gas Cylinder.

•  Never fill the LP Gas Cylinder more than 80% of cylinder 

volume. (20 lb. maximum) Do not ask the propane 
supplier to over-fill the Cylinder.

•  If you obtain LP gas through a cylinder exchange dealer, 

make sure you get a safe and adequate cylinder. Use only 
a licensed LP Gas Cylinder dealer.

WARNING

!

The LP Gas Cylinder, for use with this LP gas grill, 
must meet the following requirements:

1. 12” diameter x 18” tall, 20 lb. maximum capacity

2. Overfill Prevention Device (OPD) safety feature 

(should be noted on cylinder)

3. Must be constructed and marked in accordance with 

Specifications for LP Gas Cylinders of the U.S. De-
partment of Transportation (DOT) or the National 
Standard of Canada, CAN\CSA-B339, Cylinders, 
Spheres and Tubes for Transportation of Dangerous 
Goods; and Commission, as applicable (See collar 
for marking)

4. Must have collar to protect LP Gas Cylinder valve.

5. Must be marked “PROPANE.”

6. Must be provided with a cylinder connection device 

that is compatible with the grill’s connection.

Any use or alteration of this unit not intended could be unsafe and will void your warranty.

• If you see, smell, or hear the hiss of LP gas escap-

ing from the cylinder:

     1. Do not attempt to light appliance.
     2. Extinguish any open flame.
     3. Disconnect from fuel supply.

LP Gas Cylinder

DA N G E R

!

Содержание Vantage 6703T80K8





































Отзывы: