background image

14

LP Hose and Regulator

To reduce the risk of serious bodily injury or death 

from fire or explosion:

• Clean and inspect the gas hose/regulator before 

each use of the outdoor cooking gas appliance. 
The gas hose/regulator must be replaced prior to 
being used, if there is evidence of excessive abra-
sion or wear, or if the hose is cut or leaks. 

• Use only the gas hose/regulator assembly that 

has been supplied with this gas grill. Do not 
use hose/regulator from another manufacturer. 
Replacement gas hose/regulator assembly must be 
specified by this grill’s manufacturer before using.

• Always check for gas leaks when you connect 

and disconnect the hose/regulator to the LP Gas 
Cylinder, especially after a period of storage (for 
example, over winter).

• Make sure there are no sharp bends in the hose.
• Make sure the hose/regulator does not contact any 

heated surfaces.

WARNING

!

NOTE:

 

If the hose/regulator assembly is not working properly 
and you need a replacement, contact 

Customer Service 

at 1-800-251-7558

 or go to 

www.aussiegrills.com

.

Be sure to 

have the grill model number and serial 

number

 printed on the black label, located inside the 

left door of the cabinet. 

If you need a replacement 

part under warranty, a proof of purchase will be 

necessary

. You will be asked to forward your proof of 

purchase via e-mail or to fax your proof of purchase 
to 423-639-1055 and reference your model and serial 
number. 

It is important to register your grill and 

retain your receipt.

Connecting LP Gas Cylinder

1. Fill empty OPD LP Gas Cylinder at your local gas supplier. 

2. Place the LP Gas Cylinder in the large hole in the Bottom Panel inside the cabinet. Lock the LP Cylinder in place by 

tightening wing bolt on the outside rear of the cart base so that it seats against the ring base of the LP Cylinder.

3. Remove the protective cap from the LP Gas Cylinder valve. (Save cap for re-capping.)                                        

Route the regulator hose UNDER the Leg Brace.

 Hold Regulator in a straight line with LP Gas Cylinder valve 

so the connection does not cross thread. Insert Regulator Nipple into the LP Gas Cylinder valve. Hand tighten 
coupling nut in clockwise direction. DO NOT USE TOOLS.

Disconnecting LP Gas Cylinder

1. Turn all Control Knobs to the “Off” position and turn the handle on the 

LP Gas Cylinder clockwise until it stops.

2. Turn coupling nut on regulator counterclockwise until regulator is 

released from the threaded LP Gas Cylinder nozzle.

3. Place the protective cap over LP Gas Cylinder nozzle.

Cylinder nozzle 

faces out toward 

front of grill

Wing Bolt on outside 

rear of cart base

Hand-tighten 

coupling nut in 

clockwise direction

Route regulator hose UNDER Leg Brace

To reduce the risk of serious bodily injury or death 

from fire or explosion:

• Be sure to route the regulator hose, from the side 

burner valve to the tank, UNDER THE LEG BRACE, 
as shown below.

WARNING

!

Содержание Vantage 6703T80K8





































Отзывы: