Aussie 7202 Скачать руководство пользователя

Страница: 1 / 36

Aussie

LP Gas Grill

Assembly and Use Manual

FOR YOUR SAFETY

If you smell gas:

1. Shut off gas to the appliance.
2. Extinquish any open flame.
3. Open Lid.
4. If odor continues, immediately call your gas

supplier or your fire department.

FOR YOUR SAFETY

1. Do not store or use gasoline or other

flammable vapors and liquids in the
vicinity of this or any other appliance.

2. An LP cylinder not connected for use

shall not be stored in the vicinity of this
or any other appliance.

•READ AND FOLLOW INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY

OR USE. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT
IN DEATH, SERIOUS BODILY INJURY, AND/OR PROPERTY LOSS.

•FOR OUTDOOR HOUSEHOLD USE ONLY. NOT FOR COMMERCIAL USE.
•SOME PARTS MAY CONTAIN SHARP EDGES - ESPECIALLY WHERE

NOTED IN THIS MANUAL! WEAR PROTECTIVE GLOVES IF NECESSARY.

•THESE INSTRUCTIONS MUST BE KEPT WITH THE CONSUMER AND

RETAINED FOR FUTURE USE.

•PORCELAIN COATING CAN CHIP DURING ASSEMBLY. WEAR SAFETY

GLASSES WHILE ASSEMBLING GRILL.

For Customer Service, call

1-800-251-7558

www.aussiegrill.com

This owners manual is intended for the following models:

7462, 7402, 7362, 7302, 7262, 7202

©Aussie™ Grill Company 2001

Bonza

Bonza Deluxe

Kanga

Содержание 7202





































Результаты поиска

Содержание 7202

Отзывы:

Похожие инструкции для 7202

Бренды по названию

Популярные бренды

Aussie 7202, Инструкция по сборке и использованию

Результаты поиска

Содержание 7202

Отзывы:

Похожие инструкции для 7202

Бренды по названию

Популярные бренды