AUO AC Unison
[AUO AC Unison Installation Guide]
[Page 27 of 44]
[February 2012 Rev. 1.0]
CAUTION - Risk of Electric Shock!
-
Do not remove micro-inverter’s cover. No user serviceable parts inside. Refer servicing to qualified service personnel.
-
Both AC and DC voltage sources are terminated inside this equipment. Each circuit must be individually disconnected
before servicing the micro-inverter.
-
When the photovoltaic module is exposed to light, it supplies a DC voltage to the micro-inverter.
-
When managing AC Unison module cables within the array, the installer must ensure they do not bend the cables beyond
their bend radius tolerances. For the AC Unison module cable, the installer must maintain a bend radius of 4 x cable O.D.
or greater.
Miscellaneous instructions for AC Unison modules
-
Do not install AC Unison modules in the rain, snow or windy conditions. Tools must be dry.
-
Artificial sunlight should not be concentrated upon the AC Unison module. Do not expose AC Unison modules to sunlight
concentrated with mirrors, lenses or other means.
-
Use appropriate safety equipment (insulated tools, insulated gloves, etc) when working on any wiring.
-
Do not use damaged or defective AC Unison modules. Place all damaged or defective modules in a carton to avoid
exposure to light. Even damaged or defective modules can produce electricity.
-
Roof mounted AC Unison modules are to be mounted over a fire resistant roof.
-
Avoid uneven shade on the AC Unison module surface. Shaded cells may become hot (“hot spot” phenomenon) which
may result in permanent damage to the module (e.g., solder joints may peel off).
-
Do not clean the glass surface with chemicals or high pressure water spray.
-
Do not cover the water drain holes of the frame. There is a risk of frost damage when the frame is filled with water.
-
AC Unison modules are heavy. Handle with care. Keep children away from the system while installing.
-
Do not expose the AC Unison module to excessive loads on the surface of the AC Unison module or twist the frame. The
glass may break.
-
Do not stand or step on the AC Unison module. The glass may be slippery, and there is a risk of injury or electric shock if
glass is broken.
-
Do not hit or put excessive load on the glass or back film. PV cells may break.
-
To avoid damage to the back sheet, do not scratch or hit the back sheet.
-
To avoid damage to the junction box, do not hit the junction box; do not pull the cables.
-
Do not scratch the output cable or bend it with force. The insulation of the output cable may break which may result in
electricity leakage or shock.
-
Do not pull the output cable excessively. The output cable connection may become loose and cause electricity leakage or
shock.
-
Do not drill holes in the frame. It may compromise the frame strength and cause corrosion of the frame.
-
Do not touch the AC Unison module with bare hands. The frame of the AC Unison module has sharp edges and may
cause injury. Wear suitable gloves, such as leather gloves with padding in the palm and finger areas.
Содержание AC UNISON
