background image

IMPORTANT NOTICES

2

Installation of overhead products requires careful planning and 
preparation. Be extremely careful when working on a vehicle with 
side curtain air bags. Do not route wires near any portion of the side 
curtain air bag assemblies. This includes anchor points in A, B, C or D 
pillars of the vehicle. Routing wires in these areas or running wires by 
the side curtain air bags can prevent the side curtain air bag from fully 
deploying which can result in personal injury to vehicle occupants. If 
you have any question regarding routing in a vehicle, please contact 
Audiovox Technical support at 1-800-225-6074.

An LCD panel and/or video monitor may be installed in a motor vehicle 
and visible to the driver only if the LCD panel or video monitor is used 
for vehicle information, system control, rear or side observation or 
navigation. If the LCD panel or video monitor is used for television 
reception, video or DVD play, the LCD panel or video monitor must be 
installed so that these features will only function when the vehicle is in 
“park” or when the vehicle’s parking brake is applied.

When connecting power and ground in a mobile video installation, 
insure that the ACC  wire is fused at the point where it is connected 
to the vehicle’s ACC wiring. Failure to do so can result in damage to 
the vehicle if a short circuit develops between the vehicle connection 
point and the mobile video product.

An LCD panel and/or video monitor used for television reception, 
video or DVD play that operates when the vehicle is in gear or when 
the parking brake is not applied must be installed to the rear of the 
driver seat where it will not be visible, directly or indirectly, to the 
operator of the motor vehicle.

WARNINGS

t

Do not use any solvents or cleaning materials when cleaning the 
video monitor.

t

Do not use any abrasive cleaners, they may scratch the screen.

t

Use only lightly dampened lint free cloth to wipe the screen if it is 
dirty.

t

Lock the LCD screen in fully closed position when not in use.

t

Before putting on headphones, always adjust the volume setting to 
OFF or lowest position.

t

Remember to leave the dome light switch in the off or auto position 
when the vehicle  is unattended, as the dome lights, if left on, can 
drain the vehicle battery.

t

Do not put pressure on the screen.

t

Caution children to avoid touching or scratching the screen, as it 
may become dirty or damaged.

Safety Precautions

For safety reasons, when changing video media, it is recommended 
that the vehicle is not in motion, and that you do not allow children to 
unfasten seat-belts to change video media or make any adjustments 
to the system. System adjustments can be accomplished using 
the remote control, while seat-belts remain fastened. Enjoy your 
AUDIOVOX entertainment system but remember that the safety of all 
passengers remains the number one priority.

Licensed under one or more of the following patents, Patent Numbers 
5,775,762, 5,927,784, and 6,678,892.

*** Important Notice***

When installing this overhead monitor there should be no 
obstructions such as extra cabling, power chokes or any other objects 
placed between this overhead and supplied mounting bracket. Failure 
to comply may cause damage to the overhead monitor and will void 
the warranty.

Содержание AVXMTG13UA
















































Отзывы: