Audiolab 8000AP, Инструкция пользователя

Страница: 13 / 24

7c: Setting Up the 8000AP - 3
Mode Setup Options
• Press to
d i s p l a y t h e
s e t u p f r o n t
page
• Press the
keys to select
Press
Dolby Pro Logic II
creates five full-bandwidth output channels from 2-channel
sources. Two different modes are available:
extends the front stereo image to include
the surround speakers for a ‘wraparound’ effect with side wall
imaging. This is effective for recordings which have strong left
or right-channel elements in the mix.
Adjustment:
allows the sound of the centre-
channel to be apportioned between the centre channel
loudspeaker and the left/right front loudspeakers, from ‘no
sound’ in the centre to ‘full’ centre performance.
Adjustment:
allows to move the sound field towards
the front or the rear, depending on how much spatial effect
there is in a stereo recording.
Adjustment:
is a post processing mode providing up to
seven sound channels from stereo matrix material. The
CGain adjustment controls the amount of subtraction of
derived centre channel material from L and R channels.
Adjustment:
in steps of 0.05
Setting mode options will only be effective if you have
multi-channel loudspeakers. If you have only two (i.e. stereo)
speakers the mode will always default to stereo, regardless of
the mode options set.
MENU
Mode Options.
• ENTER
Panorama mode
Centre Width Control
L/R :0-6 - 3 is mid point
Dimension Control
L/R :0-6 - 3 is mid point
DTS Neo:6 Music
CGain: 0.0-0.5
NOTE:
Pro Logic II Movie is pre-configured by Dolby.
Pro Logic II Music can be adjusted as follows:
On/Off
5.1 Input Bypass Level Setup
HDMI Setup
Use this screen if you are using an external analogue 5.1
source, such as a laserdisc player connected via its analogue
outputs. You cannot enable the back speakers in this mode
• Press to
d i s p l a y t h e
setup page.
• Press the
keys to select
Press
This screen is similarl to the Menu except that
there is no sound generator. Determine the levels by ear with
a suitable source. We recommend you set the levels to be
identical to the Speaker levels menu and proceed from there.
• Access the
Press
This menu allows you to map an HDMI source input to any
digital input. This routes the video portion of the HDMI signal
to the TV but disables the audio portion.
The audio
connection is made from the source component to the digital
input of your choice - optical or co-axial as needed.
• You have a source e.g. A PC, with a DVI output: you can
connect the video to the 8000AP via a DVI-HDMI cable
and connect the SPDIF output to a digital input on the
8000AP. You can now watch DVDs or stream audio or A/V
content via the 8000AP.
only
MENU
5 . 1 B y p a s s
Input Levels
• ENTER
Speaker Levels
HDMI Menu
• ENTER
Why would you want to do this?
(See Page 5 for HDCP issues).
Page 11
Checking the Setup levels
• Press the keys to select
Press the SETUP key to exit setup mode
You should now listen to some music on all your selected
channels to establish that the levels are correctly set.
• Connect a multichannel source (i.e DVD player)
• Select the input with the proper key on the remote control
The player screen will indicate the input selected, the default
mode of the information on the DVD and the volume. In the
example above, the 800AP is receiving a DTS encoded signal
in 5.1mode
The Active channel lights tell you which outputs have audio
present. The number of channels in the source material is
indicated on the display i.e. 3/2.1 = 3 front, 2 surround and
1 LFE channel.
Press the
key on the handset or the front panel to cycle
the mode options for the current source material
When you have all the channels in your system operational,
you can trim the levels using the QSet facility. This will save
you having to flip back and forth between the Setup screen
and the DVD picture.
Noise Off
•
Listening to sources
MODE
Typical DVD source material is 5.1
When receiving DTS ES Discrete (6.1) the display will look
like this:
Stereo Mix
(see P 16-17)
DVD VOL -30dB
3/2.1
3/3.1 ES Discrete
DVD VOL -30dB
DVD VOL -30dB
3/3.1 Stereo Mix