AudioCodes IPmedia 3000 Скачать руководство пользователя страница 65

Страница: 65 / 90

Version 5.8

July 2009

Installation Manual

3. Installation

To connect power using a DC terminal block crimp connector:

Remove the terminal block screw from the chassis power socket (labeled

DC IN

), by

unscrewing the two screws located on the front of the terminal block.

Connect the two insulated wires to the correct DC power outlet. Ensure that the
connections to the DC power outlet maintain the correct polarity (positive / negative).

Insert the supplied DC power feed cable crimped to the terminal block into the DC inlet
(labeled

DC IN

). Ensure that the hook on the terminal block snaps into the groove

above the DC inlet.

When power is received, the

PWR IN

LED is lit (green).

Figure

3-19: Power Feed Cable Terminated with Crimp-Connection Type DC Terminal Block

Notes:

•

To ensure power redundancy, both PEM modules must be connected to
the power source.

•

To power down the device, disconnect both DC power sources.

Содержание IPmedia 3000



























































































Результаты поиска

Содержание IPmedia 3000

Отзывы:

Похожие инструкции для IPmedia 3000

Бренды по названию

Популярные бренды

AudioCodes IPmedia 3000, Руководство по установке

Результаты поиска

Содержание IPmedia 3000

Отзывы:

Похожие инструкции для IPmedia 3000

Бренды по названию

Популярные бренды