AudioCodes IPmedia 3000 Скачать руководство пользователя страница 18

Страница: 18 / 90

Installation Manual

Document #: LTRT-94704

Mediant 3000 & IPmedia 3000

Chassis

Panel

Slot #

Implemented Blade

6310 Blade Series

8410 Blade Series

(Applicable only to Mediant 3000)

Simplex: slot covered by a blank
panel.

HA: RTM-6310 Redundancy.

Not used (covered by a blank panel).

Not used (covered by a blank
panel).

The RTM-8410 type depends on the
supported span configuration:

16-Span configuration:

Simplex: slot covered by a blank
panel.

HA: RTM-8410 providing only two
RJ-45 connectors for GbE
interfaces.

42-Span configuration:

Two SCSI

connectors and two RJ-45 connectors
for GbE interfaces (for Simplex and HA
mode).

Note:

The SCSI ports are not

used.

84-Span configuration:

Two SCSI

connectors for E1/T1 spans and two
RJ-45 connectors for GbE interfaces
(for Simplex and HA mode).

The figures below show the chassis slot assignment when implementing the 6310 or 8410
blade series:

Device Implementing 6310 Blade Series:

Figure

2-3: Front- and Rear-Panel Slot Assignment for IPmedia 3000 and Mediant 3000 Simplex

with 6310 Blades

Содержание IPmedia 3000



























































































Результаты поиска

Содержание IPmedia 3000

Отзывы:

Похожие инструкции для IPmedia 3000

Бренды по названию

Популярные бренды

AudioCodes IPmedia 3000, Руководство по установке

Результаты поиска

Содержание IPmedia 3000

Отзывы:

Похожие инструкции для IPmedia 3000

Бренды по названию

Популярные бренды