manualshive.com logo in svg

Audio bit Ten, Руководство для продвинутых пользователей

Поделиться
Скачать
Audio bit Ten Скачать руководство пользователя страница 33

ADVANCED MANUAL / bit Ten /

33

The 

bit Ten

 has five crossover filters, one per each output channel. 

Each filter allows you to set the parameters of a single output channel.

1.

  Xover L/R Link:

 modifications applied to one of the channels (right or left) will also 

 

automatically be applied to the other one. To do so, click on the blue flashing light. 

 

Xover L/R Link

 affects all Filter Setting adjustments except 

Set Distance (Delay)

.

2. 

Invert Phase:

 inverts the phase of the channel under examination by 180°. 

 

This can be done by selecting the green light which will turn on. This can be useful to 

 

solve phase alignment problems among the different filtered channels.

3. 

Filter Type: 

lets you select the different types of filters that can be assigned to channels:

 -

 

Full Range 

 -

 

Low Pass 

 -

 

High Pass  

 -

 

Band Pass

 

In STANDARD mode:

According to the speaker or speaker system selected during 

setup, suitable filter types will be available.

E.g.

 for the Front Woofer only Low Pass or Band Pass will be  

available. For the Front Mid-Hi only High Pass and Band Pass  

will be available, etc.

In EXPERT mode:

Every speaker system selected has every filter type available.

WARNING:

 In EXPERT mode, pay due attention to the filter 

 

    selection. Speakers have mechanical limits that must 

 

    not be exceeded, otherwise they could lead to permanent 

 

    damage. When you select a filter, some optimized cut-off 

 

    frequencies are set by default to avoid breaking the speakers.

    

E.g.

 if you select Low Pass for a tweeter, the default frequency is 

 

    suitable for a woofer but not for the tweeter, which may be damaged. 

4.

  Filter Model: 

lets you select the type of filter to be applied.

 

 

-

 

Linkwitz 

(default) 

 

-

 

Butterworth

When launching the 

bit Ten

 software, it suggests Linkwitz as the standard filter model for 

the speaker or speaker group connected to the corresponding channel. 

To apply the opposite (Left / Right), turn the Xover L/R Link on.

If you modify the model to Butterworth, the change will be applied to both.

8.10

 FILTER SETTINGS

8

7

STANDARD MODE

 

Full Range Low Pass High Pass Band Pass

Tweeter     x  x
Midrange  

 

 

x

Woofer   x   x
Mid-Hi     x  x
Subwoofer  

x 

 

x

Full 

x  x x  x

FILTER 

TYPE ->

EXPERT MODE

 

Full Range Low Pass High Pass Band Pass

Tweeter x  x  x  x
Midrange x 

x  x 

x

Woofer x  x x  x
Mid-Hi  x  x x  x
Subwoofer x 

x 

x 

x

Full 

x  x x  x

FILTER 

TYPE ->

Содержание bit Ten


















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды