Audio bit Ten Скачать руководство пользователя

Страница: 23 / 49

ADVANCED MANUAL / bit Ten /

Setting the source.

Turn on the system and play track 1 of the CD supplied with the

bit Ten

Set all tone controls to zero (flat).

Set balance and fader to center.

Adjust the head unit volume to the maximum undistorted output level.

If the source provides an adjustable equalizer, make sure that all controls

are set to zero (flat).

Press

BACK

to go back to the previous step.

Press

NEXT

to go ahead with the setup procedure.

Press

CANCEL

to exit the procedure.

WARNING

the head unit level must be elevated to the

maximum undistorted level

. If the head unit distortion level

can not be tested in advance, bring the volume to approximately 80% of its maximum. If the head unit

output level is set

too low

, the device will produce

ground noise

(hissing sound) when playing music

tracks. This is due to the low signal / noise ratio provided by the

bit Ten

input head unit.

If you have this problem, after you

calibrate the amplifiers sensitivity

(see 8.1.21)

, increase the head unit

volume and

repeat the bit Ten calibration procedure

as detailed in the following chapter 9.

Head unit input-level instrument check.

You will need an oscilloscope for this instrument check.

- Connect the head unit output to the oscilloscope.

- Play track 1 of the

bit Ten

CD.

- Set tone, fader and balance controls and

the equalizer (if any) to zero (flat).

- Turn on the car.

- Adjust the volume control so that the oscilloscope shows

a sine wave with slightly cut peaks, as shown in the figure.

- Note the volume used by the head unit. It must be left in this position

for the following operations.

FL ± /FR ± /RL ± /RR ±

IN HI-LEVEL

wires

FL ± (TWL) /FR ± (TWR) /FL ± (WL) /FR ± (WR)
FL ± /FR ± /RL ± (Sub L) /RR ± (Sub R)

FL ± /FR ±

How to setup the Master high-level main inputs.

You can assign any processor input channel the identifying name of the signal coming from the source.

The available names are:

(Front Left Full);

(Front Right Full);

(Rear Left Full);

(Rear Right Full);

FLTW

(Front Left Tweeter);

FRTW

(Front Right Tweeter);

FLW

(Front Left Woofer);

FRW

(Front Right Woofer);

Sub L

(Sub Left);

Sub

(Sub Right).

The

bit Ten

will use these names to reconstruct a full range signal coming from an OEM source with a dedicated

multi-channel amplifier and assign the corresponding signal to the respective analog output.

Press

BACK

to go back to the previous step.

Press

NEXT

to go ahead with the setup procedure.

Press

CANCEL

to exit the procedure.

CLIP

Содержание bit Ten


















































Результаты поиска

Содержание bit Ten

Отзывы:

Похожие инструкции для bit Ten

Бренды по названию

Популярные бренды

Audio bit Ten, Руководство для продвинутых пользователей

Результаты поиска

Содержание bit Ten

Отзывы:

Похожие инструкции для bit Ten

Бренды по названию

Популярные бренды