Audio Note DAC Kit 3.1 Скачать руководство пользователя | Manualshive

Страница: 65 / 79

background image

Copyright © 2006-2011 AudioNote Kits

www.AudioNoteKits.com

[email protected]

Page 65

Section 11: Connecting the 5687 Output

Connecting the 5687 HT to the power supply

First, we need to connect the 5687 board to the M2 Power
Supply  board. The  connections  for  this  can be  seen in the
diagram shown opposite.

Take  a  red  wire  and  connect  between  the  HT  pad  on  the
5687  board  and  one  of  the  B+  pads  on  the  M2  Power
Supply board.

Take  a  black  wire  and  connect  between  the  HT  GND  pad
on  the  5687  board  and  the  GND  pad  on  the  M2  Power
Supply board.

It is a good idea to connect to one board and twist the wires
together  -  making  a  twisted  pair,  before  connecting  to  the
other board.

Connecting the Output Transformers

We essentially have two different types of output transformer when it comes to connecting up. The first (Type 1) can only
be connected in single-ended mode. The second (Type 2 - which includes Double C-Core types) can be connected in
either single-ended or balanced configuration. Please ensure that you are using the connection information that is relevant
to the transformers that you have purchased with the kit.

«
...
63
64
65
66
67
...
»

Содержание DAC Kit 3.1
















































































Отзывы:

Нет отзывов

Похожие инструкции для DAC Kit 3.1

Stratophonic SC3

Бренд: Harman Kardon Страницы: 6

Бренд: QUAD Страницы: 2

Бренд: Magtek Страницы: 54

Бренд: E-matic Страницы: 22

Бренд: Bang & Olufsen Страницы: 12

Бренд: M-Audio Страницы: 48

Бренд: B&B Electronics Страницы: 15

Бренд: G2 Страницы: 13

Бренд: CYP Страницы: 16

Бренд: MOOD Страницы: 5

Бренд: PNI Страницы: 24

Mark Levinson 5101

Бренд: Harman Страницы: 19

Бренд: ICP DAS USA Страницы: 21

Бренд: Datavideo Страницы: 23

Бренд: Laser Страницы: 21

CPSPI3700EVF380

Бренд: CyberPower Страницы: 94

LaCinema Premier

Бренд: LaCie Страницы: 24

Бренд: Intellinet Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды