Audio Note DAC Kit 3.1 страница 41 Скачать руководство пользователя | Manualshive

Страница: 41 / 79

background image

Copyright © 2006-2011 AudioNote Kits

www.AudioNoteKits.com

[email protected]

Page 41

Securing the Regulators to the Heatsink

We are now going to secure the regulators to the Heat Sink
that is installed in the chassis.

The picture opposite shows the parts that are necessary to
do this.

EXPLANATION

: It is ideal to electrically isolate the

regulator from the ground on the chassis (i.e. the heatsink)
– this way the regulator is floating – we do this with our little
insulation kit which consists of a mica layer and a plastic
insert. You can get these from the Hardware Bag marked
Heat Sink.

Begin  by  taking  one  of  the  mica
washers  and  laying  it  on  the  heatsink
as shown in the left-most picture.

The plastic insert should be fitted onto
the  screw  as  shown  in  the  central
picture.

I  would  suggest  that  you  line  up  the
mica strip with the hole in the heat sink
and install the screw and plastic insert
into the hole in the regulator.

Then  gently  screw  the  regulator  into
the  heat  sink-  the  mica  piece  may  try
and  move  so  just  gently  ease  it  back
into position.

Repeat for the second regulator.

At this point you can secure the M2
power supply board to the chassis with
one or more of the M4 screws
provided.

«
...
39
40
41
42
43
...
»

Содержание DAC Kit 3.1
















































































Отзывы:

Нет отзывов

Похожие инструкции для DAC Kit 3.1

Бренд: Rohde & Schwarz Страницы: 95

Бренд: Allen-Bradley Страницы: 4

Бренд: Allied Telesis Страницы: 50

DataBender CVX-1300

Бренд: Cypress Страницы: 28

Бренд: 3onedata Страницы: 3

Бренд: Tektronix Страницы: 211

Бренд: Rohde & Schwarz Страницы: 17

Бренд: Digitus Страницы: 3

Бренд: Digitus Страницы: 5

SCSI Differential Converter

Бренд: Black Box Страницы: 3

Бренд: Dometic Страницы: 40

Бренд: Tecsun Страницы: 2

Бренд: tams elektronik Страницы: 68

Бренд: Vanner Страницы: 16

SUNNY BOY 3600TL

Бренд: SMA Страницы: 2

Бренд: JDS Labs Страницы: 7

Бренд: Batterytech Страницы: 4

7100 Series Power Center

Бренд: Parallax Power Supply Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды