manualshive.com logo in svg

Audio Note DAC Kit 3.1, Инструкция по эксплуатации

Аудио платы Audio Note DAC Kit 3.1 является идеальным решением для всех аудиофилов. Вы можете найти подробные инструкции по сборке и использованию в бесплатном руководстве, которое доступно для скачивания на {веб-сайте}. Не упустите возможность улучшить звуковое качество вашей системы!

Поделиться
Скачать
background image

Copyright © 2006-2011 AudioNote Kits 

www.AudioNoteKits.com

 

[email protected]

  

 

Page 3 

 

Digital Board Installation .................................................................................................................................................. 56

 

Section 8: Digital Board Power Supply Connections ........................................................................................................... 57

 

Section 9: Line Board Construction ..................................................................................................................................... 58

 

Installing the Valve Bases ................................................................................................................................................ 58

 

Parts List .......................................................................................................................................................................... 58

 

Installing the Resistors ..................................................................................................................................................... 59

 

Installing the Electrolytic Capacitors................................................................................................................................. 61

 

Installing the Film (non-polarized) Capacitors .................................................................................................................. 61

 

Board Orientation ............................................................................................................................................................. 62

 

5687 Filament Wiring ....................................................................................................................................................... 62

 

Section 10: Installing I/V transformers ................................................................................................................................. 63

 

Wiring the I/V Transformers ............................................................................................................................................. 64

 

Section 11: Connecting the 5687 Output ............................................................................................................................. 65

 

Connecting the 5687 HT to the power supply .................................................................................................................. 65

 

Connecting the Output Transformers ............................................................................................................................... 65

 

Output Transformer Type 1 (Single-ended Only) ......................................................................................................... 66

 

Output Transformer Type 2 (Single-ended or Balanced) .............................................................................................. 67

 

Section 12: Source Selection and Switching ....................................................................................................................... 68

 

Installing the Input Selector Switch .................................................................................................................................. 68

 

Input Connections ............................................................................................................................................................ 69

 

Connecting the RCA Input ............................................................................................................................................ 70

 

Connecting the USB Input ............................................................................................................................................ 72

 

Connecting the XLR Input ............................................................................................................................................ 73

 

Section 13: Turn-on Procedure ............................................................................................................................................ 74

 

Final Thoughts ..................................................................................................................................................................... 75

 

Appendix .............................................................................................................................................................................. 76

 

Resistor Color Code Reference ....................................................................................................................................... 77

 

Analog Board Schematic .................................................................................................................................................. 78

 

M2 Power Supply Board Schematic ................................................................................................................................. 79

 

Содержание DAC Kit 3.1
















































































Отзывы:

Нет отзывов

Похожие инструкции для DAC Kit 3.1

Data Translation DT3153 Getting Started Manual preview
DT3153
Бренд: Data Translation Страницы: 64
Data Translation DT3152-LS Getting Started Manual preview
DT3152-LS
Бренд: Data Translation Страницы: 84
Data Translation DT3145 User Manual preview
DT3145
Бренд: Data Translation Страницы: 54
Data Translation DT3130 Series Getting Started Manual preview
DT3130 Series
Бренд: Data Translation Страницы: 54
ICP DAS USA tM-752N Series Quick Start Manual preview
tM-752N Series
Бренд: ICP DAS USA Страницы: 7
Burmester Musiccenter 151 MK2 Operation Manual preview
Musiccenter 151 MK2
Бренд: Burmester Страницы: 54
La Marche LMC SUN Series Installation And Operation Manual preview
LMC SUN Series
Бренд: La Marche Страницы: 32
3onedata IMC101B Series Quick Installation Manual preview
IMC101B Series
Бренд: 3onedata Страницы: 3
B&B Electronics Giga-McBasic-II User Manual preview
Giga-McBasic-II
Бренд: B&B Electronics Страницы: 14
VigilLink VL-SP14-1 User Manual preview
VL-SP14-1
Бренд: VigilLink Страницы: 6
CEL-MAR ADA-13110MG User Manual preview
ADA-13110MG
Бренд: CEL-MAR Страницы: 28
X-Micro XMP3-Y Quick Start Manual preview
XMP3-Y
Бренд: X-Micro Страницы: 84
SMA SUNNY BOY 3000-US User Manual preview
SUNNY BOY 3000-US
Бренд: SMA Страницы: 36
Tektronix AWG5202 Instructions Manual preview
AWG5202
Бренд: Tektronix Страницы: 11
Energizer ENA548 Owner'S Manual preview
ENA548
Бренд: Energizer Страницы: 19
LINK-MI LM-DVI-108B User Manual preview
LM-DVI-108B
Бренд: LINK-MI Страницы: 6
CYP CSC-6013 Operation Manual preview
CSC-6013
Бренд: CYP Страницы: 20
ABB DCS 600 MultiDrive Series Operating Instructions Manual preview
DCS 600 MultiDrive Series
Бренд: ABB Страницы: 80

Бренды по названию

Популярные бренды

Загрузить еще бренды