background image

Audio Authority AVAtrix, 1156 and 1166 User Manual      1

1176

1166 or 1156

Remote

Control

Xantech® 291-00

IR Receiver

or equivalent

12 Volt receiver

Xantech® 282M

IR Emitter or

equivalent

Do not use a connection

block or signal amplifier

with the 1166 or 1156.

Two-wire

IR blaster or

emitter

Connect IR receiver directly

to the Wallplate - DO NOT

use a connecting block.

-OR-

Source 1

Source 2

Source 3

Source 1

Source 2

Source  3

9878

Wallplate

Tip = Signal

Sleeve = Ground

WARNING:

 Use only

non-powered emitters,
without connecting block.

Unlike other Audio Authority products, the 1100 series has an active IR pathway, allowing it to

power the IR receivers connected to the Wallplates, and drive emitters connected to the 1166. Do

not use powered IR systems that are designed to use a separate power source or your equipment

could be damaged. The 1166 powers IR receivers with 12 volts; do not use IR receivers designed

for any other voltage.

A single emitter or
blaster may be
connected to the IR
output jack, or use the
Model 1108 when
multiple sources must
be controlled.

Tip = Signal

Ring = Ground

Sleeve = +12 Volts

WARNING:

 Connect

receivers (12V only)
directly to Wallplate,
without connecting block.

Emitter Pinout

A passive emitter usually

has a two-conductor plug.

Receiver Pinout

Receivers are powered

by 12 volts on the sleve

contact of the 9878

Wallplate IR jack.

Model 1108

IR ROUTER

Appendix A:  Using Compatible Infrared Products 

Unlike other Audio Authority products, the 1100 series has an active, 12 volt IR pathway that allows it to 
power the IR receivers connected to the Wallplates, and drive emitters connected to the 1156/66. Do not use 
powered IR systems that are designed to use a separate power source or your equipment could be damaged. 
The 1166 powers IR receivers with 12 volts; do not use IR receivers designed for any other voltage. 
Note: 1105 IR commands sent from Wallplate IR ports are not passed to the 1166 IR Output jack.

Tip = Signal

Sleeve = Ground

WARNING:

 Use only

non-powered emitters,
without connecting block.

Tip = Signal

Ring = Ground

Sleeve = +12 Volts

WARNING:

 Connect

receivers (12V only)
directly to Wallplate,
without connecting block.

Emitter Pinout

A passive emitter usually

has a two-conductor plug.

Receiver Pinout

Receivers are powered

by 12 volts on the sleeve

contact of the 9878

Wallplate IR jack.

Содержание AVAtrix

























Отзывы: