AuCom CSXI-007 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 12

AuCom CSXI-007 Скачать руководство пользователя страница 6

ADJUSTMENTS

Page 6

CSXi

710-02408-00H

Soft Stop Time

Select the soft stop ramp time (D).
Soft stop extends the time soft starter takes to
reduce voltage to zero.
The ramp time does not control the time the
motor will take to stop completely.

V

ol

ta

ge

Time

Excess Start Time

Configure the soft starter's excess start time
protection.
Select a time slightly longer than the motor
requires for a normal healthy start. The soft
starter will trip if the start does not complete
within the selected time (E).

Cur

ren

t

Time

Auxiliary Relay Function

Select the function of the soft starter's
programmable output (terminals 23, 24).
When set to "Run", the relay will operate when
the soft start is complete. When set to "Trip",
the relay will operate when the soft starter trips.

Time

Phase Sequence Protection

Configure the soft starter's phase sequence
protection.
Select the allowable phase sequences. A setting
of "Fwd" allows forward sequence (positive
rotation) only and a setting of "Any" defeats the
protection.

NOTE
Auxiliary relay function and phase rotation are configured using a shared switch. Set the
auxiliary relay function as required, then set phase rotation protection.

«
...
4
5
6
7
8
...
»

Содержание CSXI-007













Отзывы:

Нет отзывов