AuCom CSXI-007 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 12

AuCom CSXI-007 Скачать руководство пользователя страница 5

ADJUSTMENTS

710-02408-00H

CSXi

Page 5

03 246.D

1

6

4

3

2

5

8

7

Current Ramp

Current Limit

Motor Trip Class

Motor FLC

Soft Stop Time

Excess Start Time

Auxiliary Relay Function

Phase Sequence Protection

Current Ramp

Select the initial start current (A) and ramp time
(B).
Current ramp starting extends the time soft
starter takes to reach the current limit and is
suitable for generator set supplies, loads requiring
an extended start time or applications with
extreme load variation between starts.
The ramp time does not control the time the
motor will take to reach full speed.

Cur

ren

t

Time

Current Limit

Select the current limit (C).
The current limit is the maximum level of current
the soft starter will deliver to the motor during
the soft start.

Cur

ren

t

Time

Motor Trip Class

Select the trip class for motor overload
protection.
The trip class reflects the maximum time (in
seconds) that the motor can run at locked rotor
current. The Motor Trip Class setting assumes a
locked rotor current of 600%.

Setting the motor trip class to "Off" disables
motor overload protection.

Motor Full Load Current

Configure the soft starter to match the motor's
full load current (FLC).
Configure according to the motor's nameplate
current. Divide the motor's FLC by the soft
starter's maximum current rating (on the soft
starter's nameplate label).

4

Adjustments

«
...
3
4
5
6
7
...
»

Содержание CSXI-007













Отзывы:

Нет отзывов