AuCom CSXI-007 Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 12

AuCom CSXI-007 Скачать руководство пользователя страница 1

CAUTION STATEMENTS

710-02408-00H

CSXi

Page 1

Caution Statements cannot cover every potential cause of equipment damage but can highlight common
causes of damage. It is the installer's responsibility to read and understand all instructions in this manual
prior to installing, operating or maintaining the soft starter, to follow good electrical practice including
applying appropriate personal protective equipment and to seek advice before operating this equipment in
a manner other than as described in this manual.



Isolate the soft starter completely from the power supply before attempting any work on the
starter or motor.



Cables to the control inputs must be segregated from mains voltage and motor cabling.



Some electronic contactor coils are not suitable for direct switching with PCB mount relays.
Consult the contactor manufacturer/supplier to confirm suitability.



Do not apply incorrect voltages to the control input terminals.



Do not connect power factor correction capacitors to the output of CSX

i

soft starters. If static

power factor correction is employed, it must be connected to the supply side of the soft starter.

The examples and diagrams in this manual are included solely for illustrative purposes. The information
contained in this manual is subject to change at any time and without prior notice. In no event will
responsibility or liability be accepted for direct, indirect or consequential damages resulting from the use or
application of this equipment.

AuCom cannot guarantee the correctness or completeness of the translated information in this document.
In case of dispute the master document in English is the Reference Document.

WARNING - ELECTRICAL SHOCK HAZARD
CSX

i

soft starters contain dangerous voltages when connected to mains voltage. Only a qualified

electrician should carry out the electrical installation. Improper installation of the motor or the soft
starter may cause equipment failure, serious injury or death. Follow this manual and local electrical
safety codes.

GROUNDING AND BRANCH CIRCUIT PROTECTION
It is the responsibility of the user or person installing the soft starter to provide proper grounding
and branch circuit protection according to local electrical safety codes.

SHORT CIRCUIT
CSX

i

soft starters are not short circuit proof. After severe overload or short circuit, the operation

of the soft starter should be fully tested by an authorised service agent.

Ce manuel est également disponible en français à partir de www.aucom.com.

Dieses Handbuch ist auch in deutscher Sprache aus www.aucom.com.

Questo manuale è disponibile anche in italiano da www.aucom.com.

Este manual também está disponível em Português no site www.aucom.com.

Este manual también está disponible en español a partir de www.aucom.com.

该手册也可在中国从

www.aucom.com.

1

Caution Statements

© 2012 AuCom Electronics Ltd. All Rights Reserved.

1
2
3
...
»

Содержание CSXI-007













Отзывы:

Нет отзывов