ATS RTFO Скачать руководство пользователя

Страница: 5 / 34

MAN - RTFO - REV: Org | A. Introduction

A. Introduction

A.1 Unpacking

Retain all cartons and packing materials until the unit is operated and found to be in good condition. If damage has

occurred during shipping, notify Applied Test Systems (ATS) and the carrier immediately. If it is necessary to file a

damage claim, retain the packing materials for inspection by the carrier.

WARNING: Always lift from under the oven with forks or proper lifting equipment. Do not lift from

the electrical enclosure.

A.2 Warranty Information

All new ATS systems are shipped with a warranty. Units have a warranty against defective parts and workmanship for

one full year from the date of shipment. Please see APPENDIX A of this manual for complete details on the warranty.

A.3 After Sale Support

If there are any questions concerning the operation of the unit or software, contact the ATS Service Department at

+1-724-283-1212.

Before calling, please obtain the software revision number and the serial number from the unit’s data tag. A sample

data tag is illustrated below, and can be completed with the unit’s information for easy reference. Please be prepared
to give a complete description of the problem to the ATS Service Department at +1-724-283-1212.

Figure A.1: ATS Sample Data Tag

Содержание RTFO



































Результаты поиска

Содержание RTFO

Отзывы:

Похожие инструкции для RTFO

Бренды по названию

Популярные бренды

ATS RTFO, Инструкция по эксплуатации

Результаты поиска

Содержание RTFO

Отзывы:

Похожие инструкции для RTFO

Бренды по названию

Популярные бренды