background image

Call the assigned toll-free number, wait for the system to answer the call and follow the voice prompt: “This is 
Moupic’s PageAlarm Monitoring Station.  Please enter your PIN number”. 
 
After receiving a valid PIN, the system will prompt: “Please enter your Password (PW) followed by the command 
code”, after 10 seconds the system will then hang up itself. 
 
Within a couple of minutes, the anti-carjacking system will be activated.  The hazard lights will flash; the car will 
honk and be slowed down. 
 
Example: 
1.

 

Dial the assigned toll-free number; 

2.

 

After hearing the voice prompt, enter your PIN number 

3.

 

Following the voice prompt, enter your Password (PW) followed by an anti-carjacking command code which 
is shown on your Monitoring Service Card. 

 

Sending a RESET Command 

 

To RESET the anti-carjacking command, you MUST send a RESET command code to the  ATS NASA 2001.  
The RESET sequence is described as follows: 
 
1.

 

Dial the assigned toll-free number; 

2.

 

After hearing the voice prompt, enter your PIN number; and, 

3.

 

Following the voice prompt, enter your Password (PW) followed by a RESET command code that you have 
selected and that is shown on your Monitoring Service

 
Sending other Commands  

 

Refer to your Monitoring Service card to determine other telephone command capabilities of the PageAlarm™ 
2001. One of the MOST popular commands is the “Door Unlock” command.  This is especially handy if you lock 
your car key inside the car.  A simple telephone call will unlock your car doors!  Let’s imagine the “Door Unlock” 
is on Command Code XX.  Here’s how to activate this command code: 
 
1.

 

Call the assigned toll-free number 

2.

 

After hearing the voice prompt, enter your PIN number 

3.

 

After hearing the voice prompt, enter Password (PW) number followed by the Command Code for Door 
Unlock XX. 

 
Within a couple of minutes, the car doors should electronically be unlocked! 
 

NOTE:  

We strongly suggest you try ALL of the Command Codes available to your ATS NASA  2001 before 

you use them!  Get aquatinted with the system, the timing of the call and Que. of the system for you to enter 
the required numbers.  Your ATS NASA  2001 will fail to operate, if you don’t follow the EXACT 
procedures.

 

 
2. ATS NASA 2001 Monitoring Service in Other Regions

 

 

Содержание NASA 2001









Отзывы: