Atmos A85 Скачать руководство пользователя страница 15

Страница: 15 / 66

Operation and Maintenance Manual - EN

www.atmos.cz

EN-15

9. Connection of the boiler D80P, P80 with a buffer tank and

burner control by the TS and TV sensors, separate control of the

heating system by electronic control unit ACD 01 / ACD 03/04

INFO

– The TK sensor placed in boiler pocket (from production), the TV and TS sensors

(boiler accessory) on the buffer (accumulation) tank are connected directly to the burner.

Regulation of the boiler’s exhaust fan (R) and pump in boiler circuit (R2) from the burner

ATMOS A85. Regulation of the functions of the pneumatic cleaning from the burner’s

AC07X regulation with additional AC07X-C module – compressor (R5) and pneumatic el.

valve (R6).

ACD01 regulation controls the heating system only.

Required accessories

(is part of the burner): nothing needs to be bought

(ACD 01 controler is not part of the delivery)

System configuration of parameters:

S6 = 3, S14 = 12, S15 = 2, S67 = 15, S68 = 16

The pump in the boiler circuit is controled directly from the control unit of the ATMOS A85 burner

(the pump thermostat placed on the boiler control panel connected in series with output R2 - factory

settings).

MAX. 60°C

(R2) 75 °C

filtr

filter

mísící ventil

mixing valve

čerpadlo

pump

obytné místnosti

haritable rooms

tlakoměr, přetlakový ventil,

odvzdušňovací ventil

pressure gauge, safety

valve, deaerator

tlaková

expansní

nádoba

pressure

expansion

vessel

ventil

valve

ventil

valve

filtr

filter

ventil

valve

bojler TUV

DHW boiler

ventil

valve

ventil

valve

ventil

valve

ventil

valve

A85

odvzdušňovací

ventil deaerator

vyrovnávací nádrž

buffer tank

1000 l

Laddomat 22

A85

filtr

filter

ventil

valve

termoregulační ventil

thermoregulatory valve

VF1

MKP1

SLP

SDW10/20

ARU5/10/30

ATMOS

ACD

odtahový ventilátor

exhaust fan

Содержание A85



































































Результаты поиска

Содержание A85

Отзывы:

Бренды по названию

Популярные бренды

Atmos A85, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание A85

Отзывы:

Бренды по названию

Популярные бренды