Atlantic alfea excellia duo 11 Скачать руководство пользователя страница 64

Страница: 64 / 72

6 .3 Faults displayed

on the single phase outdoor unit

To access the electronic board, you must remove the

front (right-hand) facing from the outdoor unit.
Faults are coded by diode flashes.

When an error occurs:

- The diode "

ERROR

" (2) blinks.

- Press once on the switch "

ENTER

" (SW3).

- The "

ERROR

" (2) diode blinks several times depending

on the error's type

(see below).

Diode display

Error contents

1 Flash

Serial forward transfer error.

2 Flashes

Discharge thermistor error.

3 Flashes

Pressure sensor error.

4 Flashes

Heat-exchange thermistor (outlet) error.

5 Flashes

Heat-exchange thermistor (intermediate) error.

6 Flashes

Expansion valve thermistor error.

7 Flashes

Outdoor temperature thermistor error.

8 Flashes

Compressor thermistor error.

9 Flashes

Heat sink thermistor error.

11 Flashes

Discharge temperature protection (permanent stoppage).

12 Flashes

Compressor temperature protection (permanent stoppage).

13 Flashes

Current trip (permanent stoppage).

14 Flashes

Detection of compressor position error (permanent stoppage).

15 Flashes

Compressor start up error (permanent stoppage).

16 Flashes

Fan motor 1 error (permanent stoppage).

17 Flashes

Fan motor 2 error (permanent stoppage).

18 Flashes

Inverter error.

19 Flashes

Active filter error.

20 Flashes

Low pressure abnormal.

21 Flashes

Connection with hydraulic unit error.

22 Flashes

Hydraulic unit abnormality condition.

Ensure that the general electrical power supply has been cut off before starting any repair work.

When the HP is not under tension, protection frost-free is not assured.

figure 51 - Location of switches and diodes

on single phase outdoor unit

SW1

SW2

SW3

SW4

SW5

(1)

(2)

(3)

(4)

(5)

Diodes

and switches

Installation and operating manual "1572 - EN"

Heat pump air/water split 2 services alféa excellia duo

- 64 -

Ensure that the general electrical power supply has been cut off before starting any repair work.

When the HP is not under tension, protection frost-free is not assured.

Содержание alfea excellia duo 11









































































Результаты поиска

Содержание alfea excellia duo 11

Отзывы:

Похожие инструкции для alfea excellia duo 11

Бренды по названию

Популярные бренды

Atlantic alfea excellia duo 11, Инструкция по установке и эксплуатации

Результаты поиска

Содержание alfea excellia duo 11

Отзывы:

Похожие инструкции для alfea excellia duo 11

Бренды по названию

Популярные бренды