Atlanta EVA Скачать руководство пользователя страница 26

Страница: 26 / 32

Rev.0 13/01/2020

Operator Panel | TURNTABLE - MAST

2.5

E01

Transpallet photocell

interrupted

-The safety photocell is activated.
-The photocell has no obstacles but

the signal does not get to the card.

-Remove the obstacle / check the mirror on the

safety photocell.

-Make sure the photocell is operating and the LED

changes status when an obstacle is inserted. If it

is not working, replace it. Check the continuity of

the cable with the signals on the panel 1+ and

8.3. Replace if broken.

E02

Rotation or running

anomaly, motor blocked

-The sensor does not read the

petals because it is too far from the

phonic wheel.

-The sensor does not read the

petals because the phonic wheel is

broken or crooked.

-The sensor does not send the

signal to the card.

-The motor seems to rotate at less

than 500 rpm for more than 2.5 s.

-The machine does not move, even

with manual controls.

-Adjust the position of the sensor compared to

the petals of the phonic wheel (distance < 2 mm).

-Fix / replace the phonic wheel.
-Check the correct operation of the sensor,

bringing it close to a metallic object. If the LED

lights up, replace the cable, if the sensor does

not work, it needs to be replaced.

not slippery. If the alarm occurs during slowing,

the sensor is not reading all the petals of the

phonic wheel.

-The drive or inverter does not receive

consent to start, check the wiring.

The

drive

inverter

faulty,

communicate the code shown on the

latter. For a DC motor, check the brushes.

The motor cable is not connected well, check

the wiring and tightness, even on the brake, if

present. The electromechanical brake on the

motor, if present, may not release. If this occurs,

it must be adjusted or replaced. The motor unit

may be damaged or defective; replace it.

E03

Restart after power

outage.

-The card restarted.
-The machine shut down and shows

this warning.

-Press the RESET key.
-There was a power outage and the machine

shut down and then restarted: Press the RESET

button (no power) or bell (touch).

E04

Carriage, crush

prevention limit switch

triggered

-Obstacle below the carriage.
-The E04 alarm persists without any

obstacle.

-Remove the obstacle and press RESET.
-Check the proper mechanical operation of the

micro and the crush-prevention plate. If a sensor

is broken or the plate is deformed, they must

be replaced. Check the electrical contacts and

that the signal reaches the card. If the sensor is

broken or the cable is interrupted, replace it.

Содержание EVA

































Результаты поиска

Содержание EVA

Отзывы:

Похожие инструкции для EVA

Бренды по названию

Популярные бренды

Atlanta EVA, Руководство пользователя

Результаты поиска

Содержание EVA

Отзывы:

Похожие инструкции для EVA

Бренды по названию

Популярные бренды