•
Use only
connecting attachments
with a rubber plug device
for severe requirements
that is protected against spraying
water.
•
Check
connecting attachments
for defects or ageing before using
them.
•
Never use defective
connecting attachments
.
•
When laying the
connecting attachments
, be sure that they do
get crushed or bent, and that the plug-and-socket connection does
not get wet.
•
Do not use any
temporary electrical connections.
•
Never bridge over
protective devices
or put them out of operation.
•
Only connect with residual current circuit breaker (30 mA).
A licensed professional electrician must make all
electrical
connections and repairs
, and observe local regulations in doing so,
especially those regarding protective measures.
The manufacturer or a company designated by the manufacturer
must attend to
the repair of all electrical parts
on the machine.
6
S
S
t
t
a
a
r
r
t
t
-
-
u
u
p
p
Observe all safety instructions
.
Setting up the machine:
•
Set up the machine on a solid, level
base
.
•
Keep the machine from
sinking
into the ground or floor.
Adhere to accident prevention regulations (danger of tipping).
•
When
setting up
the machine, make sure that the mixing drum
can be emptied without obstruction.
Switching on and off
Be sure that
-
all protective devices are on the mixer and properly mounted.
-
all safety instructions are adhered to.
•
Switch the motor on and off
only at the switch
.
•
In the event of a power failure, the machine will switch off
automatically
. Press the switch again to restart the machine.
Motor protection
The motor is equipped with a
thermostat
. The thermostat switches the
motor off automatically in the event of overload (overheating). The
machine can be restarted after a
cooling-off period
.
M
M
i
i
x
x
i
i
n
n
g
g
•
Only use mixer for applications listed under ”Correct use“.
•
Check the stability of the mixer.
•
Only fill or empty the mixing drum while the motor is running.
•
Observe the nominal filling volume!
•
An electrical safety shutdown prevents the mixer operating while
the safety grid is open. Check functionality of safety shutdown
before commissioning.
Mixture production:
1.
Close safety grid.
2.
Switch on mixer.
3.
Fill with water and aggregate (sand, ...).
4.
Add binding agent (cement, lime, ...).
5.
Repeat points 3 and 4 until required mixture ratio has been
achieved.
6.
Blend mixture well.
Have a professional advise you regarding the composition and
quality of the material being mixed.
Prepared (commercially available) mixture production:
Observe mixing ratio and details given by manufacturer on packaging.
1.
Close safety grid.
2.
Switch on mixer.
3.
Fill with required volume of water.
4.
There is a sack opener on the safety grid which is used to tear
open the packed mixture and filling the drum.
5.
Blend mixture well.
Emptying the mixing drum:
The drum is emptied through an opening in the base which is opened
by actuating a lever.
See page 29 for instructions on emptying.
T
T
r
r
a
a
n
n
s
s
p
p
o
o
r
r
t
t
Pull plug each time before transport.
For loading see page 30.
S
S
t
t
o
o
r
r
a
a
g
g
e
e
The mixer should be cleaned thoroughly before long storage periods
and moving parts treated with an environmentally-friendly spray oil.
This lengthens the useful life of a mixer and ensures smooth operation
of the device.
C
C
l
l
e
e
a
a
n
n
i
i
n
n
g
g
Additional safety instructions
Pull plug each time before cleaning.
•
Switch off machine and
pull plug
if you have to touch the machine
(with hand, brush, scraper, rag, etc.) while cleaning it.
•
Protective devices
removed for cleaning must be properly
remounted before starting the machine.
•
Do not spray the motor and switch directly with a water jet.
•
Remove agitator head to clean (
see page 30).
Notes on cleaning:
•
Before taking a
break
and after
finishing work
, clean the mixer
inside and out.
•
Do not beat on the mixing drum
with hard objects
(hammer,
shovel, etc.). A dented mixing drum impairs mixing operations and
is difficult to clean, besides.
Содержание COMPACT 100 -
Страница 35: ......
